u-boot.git/include/configs/arndale.h, branch master

ARM: psci: move GIC address override to Kconfig

2023-10-11T17:22:32+00:00

As the code to switch an ARM core from secure to the non-secure state
needs to know the base address of the Generic Interrupt Controller
(GIC), we read an Arm Cortex defined system register that is supposed to
hold that base address. However there are SoCs out there that get this
wrong, and this CBAR register either reads as 0 or points to the wrong
address. To accommodate those systems, so far we use a macro defined in
some platform specific header files, for affected boards.

To simplify future extensions, replace that macro with a Kconfig variable
that holds this override address, and define a default value for SoCs
that need it.

Signed-off-by: Andre Przywara 
Reviewed-by: Sam Edwards

global: Migrate CONFIG_SMP_PEN_ADDR to CFG

2022-12-23T15:15:12+00:00

Perform a simple rename of CONFIG_SMP_PEN_ADDR to CFG_SMP_PEN_ADDR

Signed-off-by: Tom Rini

global: Migrate CONFIG_ARM_GIC_BASE_ADDRESS to CFG

2022-12-23T15:07:03+00:00

Perform a simple rename of CONFIG_ARM_GIC_BASE_ADDRESS to CFG_ARM_GIC_BASE_ADDRESS

Signed-off-by: Tom Rini

arm: samsung: Migrate a number of symbols to Kconfig

2022-06-28T21:04:37+00:00

- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
  CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
  of U-Boot usage.

Cc: Minkyu Kang 
Signed-off-by: Tom Rini

Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h

2022-06-06T16:09:19+00:00

- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
  pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
  set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
  GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
  board config header files.

Signed-off-by: Tom Rini

treewide: configs: get rid of unused CONFIG_DEFAULT_CONSOLE

2020-10-15T04:33:22+00:00

These are all unused.

Signed-off-by: Andre Heider 
Signed-off-by: Heinrich Schuchardt 
Acked-by: Krzysztof Kozlowski 
Reviewed-by: Simon Glass 
Signed-off-by: Minkyu Kang

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06+00:00

This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford 
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk 
Cc: Joe Hershberger 
Cc: Patrick Delaunay 
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini 
Acked-by: Joe Hershberger 
Reviewed-by: Simon Goldschmidt

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

2019-08-02T15:19:14+00:00

This converts the following to Kconfig:
   CONFIG_USE_PREBOOT
   CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass

Add CONFIG_USE_PREBOOT to boards that use CONFIG_PREBOOT

2019-08-02T15:17:58+00:00

In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be
defined for each board. To prepare for conversion to Kconfig, add this.

Signed-off-by: Simon Glass