u-boot.git/include/configs/bg0900.h, branch master

arm: Remove bg0900 board

2021-10-02T01:08:19+00:00

This board has not been converted to CONFIG_DM by the deadline.
Remove it.

Cc: Marek Vasut 
Signed-off-by: Tom Rini

Convert CONFIG_SYS_LOAD_ADDR to Kconfig

2021-08-31T21:46:37+00:00

Now that we have consistent usage, migrate this symbol to Kconfig.

Signed-off-by: Tom Rini 
Reviewed-by: Rick Chen

global: Convert CONFIG_LOADADDR to CONFIG_SYS_LOADADDR

2021-08-31T21:46:37+00:00

- In most of the codebase, we reference CONFIG_SYS_LOAD_ADDR and not
  CONFIG_LOADADDR.
- Generally, CONFIG_SYS_LOADADDR is set to CONFIG_LOADADDR and then as
  noted, we use CONFIG_SYS_LOADADDR.

Signed-off-by: Tom Rini

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06+00:00

This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford 
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk 
Cc: Joe Hershberger 
Cc: Patrick Delaunay 
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini 
Acked-by: Joe Hershberger 
Reviewed-by: Simon Goldschmidt

cosmetic: config: Remove empty #ifdefs

2019-04-02T11:44:18+00:00

After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.

Remove them to clean u-boot source code.

Signed-off-by: Lukasz Majewski

Convert CONFIG_ENV_SPI_* to Kconfig

2019-03-25T21:36:59+00:00

This converts the following to Kconfig:
  CONFIG_ENV_SPI_BUS
  CONFIG_ENV_SPI_CS
  CONFIG_ENV_SPI_MAX_HZ
  CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay

Convert CONFIG_DEFAULT_SPI_* to Kconfig

2019-03-25T21:36:53+00:00

This converts the following to Kconfig:
   CONFIG_DEFAULT_SPI_BUS
   CONFIG_DEFAULT_SPI_MODE

Signed-off-by: Patrick Delaunay

Convert CONFIG_SF_DEFAULT_* to Kconfig

2019-03-25T21:36:53+00:00

This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02+00:00

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini