u-boot.git/include/configs/cpu9260.h, branch v2014.10

at91: remove redundant AT91FAMILY definition in board config file

2014-05-26T22:10:52Z

Now the AT91FAMILY is already defined in the at91 SoC header. The at91 board config file will include the SoC header file. So we can remove the redundant AT91FAMILY definition in at91 board config files. Signed-off-by: Josh Wu [rebase patch] Signed-off-by: Andreas Bießmann

at91: nand: switch atmel_nand to generic GPIO API

2013-12-09T12:21:45Z

Signed-off-by: Andreas Bießmann Acked-by: Jens Scharsig (BuS Elektronik) Tested-by: Jens Scharsig (BuS Elektronik) Acked-by: Scott Wood

arm926ejs, at91: add common phy_reset function

2013-12-01T21:38:52Z

add common phy reset code into a common function. Signed-off-by: Heiko Schocher Cc: Andreas Bießmann Cc: Bo Shen Cc: Jens Scharsig Cc: Sergey Lapin Cc: Stelian Pop Cc: Albin Tonnerre Cc: Eric Benard Cc: Markus Hubig Acked-by: Jens Scharsig (BuS Elektronik) Tested-by: Jens Scharsig (BuS Elektronik) Tested-by: Bo Shen Acked-by: Bo Shen Signed-off-by: Andreas Bießmann

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

2013-11-09T21:59:47Z

Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h

arm: atmel: get rid of too many ifdeffery

2013-11-04T19:32:37Z

Get rid of too many ifdeffery in usb ohci driver Add following two configuration for USB clock selecting - CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock - CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock Signed-off-by: Bo Shen Signed-off-by: Andreas Bießmann

config: remove platform CONFIG_SYS_HZ definition part 2/2

2013-11-04T16:06:16Z

Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38Z

Signed-off-by: Wolfgang Denk [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini

ARM: Remove unused stack and irq config defines

2012-09-01T12:58:22Z

CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present in most ARM board config files. IRQs are only enabled for 1 config, so remove the unused config options for IRQ and FIQ stack size as well. Cc: Albert ARIBAUD Signed-off-by: Rob Herring

CONFIG_SYS_BAUDRATE_TABLE: Add , place there

2012-06-20T18:26:16Z

We provide a default table of { 9600, 19200, 38400, 57600, 115200 } in which mkconfig places after in the generated config file. This is used when a board has not set its own table. Signed-off-by: Tom Rini

NAND: remove NAND_MAX_CHIPS definitions

2012-01-26T22:08:55Z

This change follows the change by Wolfgang Grandegger (commit 6c869637fef), which allows to remove useless NAND_MAX_CHIPS definitions in board config files. Signed-off-by: Vladimir Zapolskiy Cc: Wolfgang Grandegger Cc: Scott Wood Signed-off-by: Scott Wood