- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.

Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>

CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.

All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.

These results have been confirmed with tools/moveconfig.py.

Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_NAND_LPC32XX_SLC

Signed-off-by: Adam Ford <aford173@gmail.com>

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
	- edb9315a	- CONFIG_PHYLIB is not enabled. Entry is
			  deleted.

	- ds414		- CONFIG_PHYLIB is in incompatible format:
			  { 0x1, 0x0 }. This entry is also deleted.

	- devkit3250	- The PHY_ADDR is in hex format (0x1F).
			  Manually CONFIG_PHY_ADDR=31 is added in
			  the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>