u-boot.git/include/configs/devkit3250.h, branch v2020.10

Convert CONFIG_SPL_NAND_DRIVERS et al to Kconfig

2020-07-28T20:18:10+00:00

This converts the following to Kconfig:
   CONFIG_SPL_NAND_DRIVERS
   CONFIG_SPL_NAND_ECC
   CONFIG_SPL_NAND_SIMPLE

Signed-off-by: Adam Ford

spi: Zap lpc32xx_ssp driver-related code

2020-05-10T20:00:49+00:00

lpc32xx_ssp driver is deprecated, no active updates
and no board user, hence dropped the same.

Cc: Vladimir Zapolskiy 
Cc: Albert ARIBAUD 
Cc: Tom Rini 
Signed-off-by: Jagan Teki

treewide: mem: Move mtest related defines to Kconfig

2020-05-08T16:02:56+00:00

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma 
Signed-off-by: Michal Simek 
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini

Convert CONFIG_PHYLIB et al to Kconfig

2020-04-28T19:57:58+00:00

This converts the following to Kconfig:
   CONFIG_PHYLIB
   CONFIG_BITBANGMII
   CONFIG_MV88E6352_SWITCH
   CONFIG_MV88E61XX_SWITCH
   CONFIG_PHYLIB_10G
   CONFIG_PHY_AQUANTIA
   CONFIG_PHY_ATHEROS
   CONFIG_PHY_BROADCOM
   CONFIG_PHY_CORTINA
   CONFIG_PHY_DAVICOM
   CONFIG_PHY_ET1011C
   CONFIG_PHY_LXT
   CONFIG_PHY_MARVELL
   CONFIG_PHY_MICREL
   CONFIG_PHY_NATSEMI
   CONFIG_PHY_REALTEK
   CONFIG_RTL8211X_PHY_FORCE_MASTER
   CONFIG_PHY_SMSC
   CONFIG_PHY_TERANETICS
   CONFIG_PHY_TI
   CONFIG_PHY_VITESSE
   CONFIG_PHY_XILINX

Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk 
Cc: Joe Hershberger 
Cc: Patrick Delaunay 
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini 
Acked-by: Joe Hershberger 
Reviewed-by: Simon Goldschmidt

mtd: nand: raw: Move CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig

2019-08-26T00:58:37+00:00

Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.

Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.

Signed-off-by: Stefan Roese 
Cc: Eugen Hristev 
Cc: Miquel Raynal 
Cc: Gregory CLEMENT 
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini

CONFIG_SYS_[DI]CACHE_OFF: convert to Kconfig

2019-05-18T12:15:34+00:00

CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.

All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.

These results have been confirmed with tools/moveconfig.py.

Acked-by: Alexey Brodkin 
Signed-off-by: Trevor Woerner 
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

2019-04-30T01:41:40+00:00

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt 
[trini: Re-run migration]
Signed-off-by: Tom Rini

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

2018-10-19T23:19:50+00:00

This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford 
[trini: Re-migrate]
Signed-off-by: Tom Rini

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02+00:00

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini