u-boot.git/include/configs/flea3.h, branch v2012.07

mxc_i2c: specify i2c base address in config file

2012-07-11T08:54:29+00:00

The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.

Signed-off-by: Troy Kisky 
Acked-by: Stefano Babic

hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c

2012-06-20T18:36:51+00:00

Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic 
Signed-off-by: Tom Rini 
Acked-by: Stefano Babic

CONFIG_SYS_BAUDRATE_TABLE: Add , place there

2012-06-20T18:26:16+00:00

We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in  which mkconfig places after  in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini

include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF

2012-05-15T06:31:28+00:00

This define does not control anything, remove it.

Signed-off-by: Tom Rini

mx35: flea3: fix when cache functions are linked

2012-04-16T12:53:59+00:00

Signed-off-by: Stefano Babic

configs: Remove CONFIG_NET_MULTI from board files

2012-02-12T09:11:26+00:00

CONFIG_NET_MULTI is not used anymore, so remove it from board files.

Cc: Marek Vasut 
Cc: Stefano Babic 
Cc: Kumar Gala 
Cc: Sandeep Paulraj 
Signed-off-by: Fabio Estevam 
Acked-by: Tom Rini 
Acked-by: Mike Frysinger 
Acked-by: Marek Vasut 
Acked-by: Heiko Schocher 
Acked-by: Kumar Gala 
Acked-by: Stefano Babic 
Tested-by: Marek Vasut 
Tested-by: Heiko Schocher

MX35: flea3: changes due to hardware revision B

2011-12-06T22:59:40+00:00

Revision B of the board uses CSD0 for the DRAM,
as usual for MX3 boards. The patch fixes also
some values in the U-Boot environment.

Signed-off-by: Stefano Babic

MX: serial_mxc: cleanup removing nasty #ifdef

2011-12-06T22:59:40+00:00

The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS__
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.

Signed-off-by: Stefano Babic 
CC: Marek Vasut 
CC: Wolfgang Denk 
CC: Fabio Estevam 
CC: Helmut Raiger 
CC: John Rigby 
CC: Matthias Weisser 
CC: Jason Liu 
Acked-by: Jason Liu

MX35: add support for flea3 board

2011-11-03T21:56:20+00:00

The flea3 board is a custom board by CarMediaLab used
in automotive.
Network (FEC), NOR, NAND and SPI are supported.

Signed-off-by: Stefano Babic