Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS

Signed-off-by: Tom Rini <trini@konsulko.com>

This removes the following unreferenced CONFIG symbols:
   CONFIG_FDTADDR
   CONFIG_FDTFILE
   CONFIG_FLASH_SECTOR_SIZE
   CONFIG_FSL_CPLD
   CONFIG_HDMI_ENCODER_I2C_ADDR
   CONFIG_I2C_MVTWSI
   CONFIG_I2C_RTC_ADDR
   CONFIG_IRAM_END
   CONFIG_IRAM_SIZE
   CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
   CONFIG_L1_INIT_RAM
   CONFIG_MACB_SEARCH_PHY
   CONFIG_MIU_2BIT_21_7_INTERLEAVED
   CONFIG_MTD_NAND_VERIFY_WRITE
   CONFIG_MVGBE_PORTS
   CONFIG_NETDEV
   CONFIG_NUM_DSP_CPUS
   CONFIG_PHY_BASE_ADR
   CONFIG_PHY_INTERFACE_MODE
   CONFIG_PSRAM_SCFG
   CONFIG_RAMBOOT_SPIFLASH
   CONFIG_RAMBOOT_TEXT_BASE
   CONFIG_RD_LVL
   CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
   CONFIG_SETUP_INITRD_TAG
   CONFIG_SH_QSPI_BASE
   CONFIG_SMDK5420
   CONFIG_SOCRATES
   CONFIG_SPI_ADDR
   CONFIG_SPI_FLASH_QUAD
   CONFIG_SPI_FLASH_SIZE
   CONFIG_SPI_HALF_DUPLEX
   CONFIG_SPI_N25Q256A_RESET
   CONFIG_TEGRA_SLINK_CTRLS
   CONFIG_TPM_TIS_BASE_ADDRESS
   CONFIG_UBOOT_SECTOR_COUNT
   CONFIG_UBOOT_SECTOR_START
   CONFIG_VAR_SIZE_SPL
   CONFIG_VERY_BIG_RAM

And also:
   BL1_SIZE
   PHY_NO
   RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

- Ensure that everyone setting mtdids= and mtdparts= is doing so via the
  CONFIG options.
- If the CONFIG options are set, ensure that the default environment
  sets mtdparts / mtdids.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_BOARD_SIZE_LIMIT

To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_88F5182
   CONFIG_BOARD_IS_OPENRD_BASE
   CONFIG_BOARD_IS_OPENRD_CLIENT
   CONFIG_BOARD_IS_OPENRD_ULTIMATE
   CONFIG_D2NET_V2
   CONFIG_FEROCEON
   CONFIG_FEROCEON_88FR131
   CONFIG_INETSPACE_V2
   CONFIG_KW88F6192
   CONFIG_KW88F6281
   CONFIG_KW88F6702
   CONFIG_NET2BIG_V2
   CONFIG_NETSPACE_LITE_V2
   CONFIG_NETSPACE_MAX_V2
   CONFIG_NETSPACE_MINI_V2
   CONFIG_NETSPACE_V2
   CONFIG_SHEEVA_88SV131

At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_USE_BOOTCOMMAND
   CONFIG_BOOTCOMMAND
   CONFIG_RAMBOOTCOMMAND
   CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>

The mvsata_ide driver was due for DM conversion by v2019.07.  As that
has long passed, remove the driver and disable it in the boards which
had enabled it.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_BZIP2
   CONFIG_GZIP
   CONFIG_LZO
   CONFIG_ZLIB
   CONFIG_LZMA
   CONFIG_LZO

Signed-off-by: Tom Rini <trini@konsulko.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>