u-boot.git/include/configs/km, branch v2011.09

Drop bogus BOOTFLAG_* definitions

2011-09-20T11:18:07+00:00

There is no code anywhere that references BOOTFLAG_* so remove these
defines.

Signed-off-by: Wolfgang Denk 
Cc: Heiko Schocher 
Cc: Valentin Longchamp 
Cc: Peter Tyser

km/common: moved eeprom config to pbec specific part

2011-07-28T13:40:02+00:00

Moved eeprom config to specific part, to allow bigger eeprom write pages
for km_kirkwood designs. Write page only used for env eeprom in std use
cases. 24C128 has page size of 64bytes -> 8 time faster.

Signed-off-by: Stefan Bigler 
cc: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk

km/common: use u-boot.kwb for u-boot update function on arm

2011-07-28T13:39:44+00:00

Now we use the standard u-boot make to build the Kirkwood binary.
The output file is u-boot.kwb. So use this name for the tftp
update function to avoid confusion, because this is the binary we
need on Kirkwood.

Signed-off-by: Holger Brunck 
cc: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk

km/common: enable cramfs and cramfs cmdline

2011-07-27T21:44:40+00:00

All the km boards uses CRAMFS images where the kernel is stored.
This isn't architecture specific because we use it on ARM and
POWERPC.

Signed-off-by: Holger Brunck 
Signed-off-by: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk

powerpc/km82xx: remove 82xx specific functions from common.c

2011-07-27T21:44:35+00:00

Common code should be valid for more than one architecture,
therefore the km82xx specific code was removed from common.c.

Signed-off-by: Holger Brunck 
Signed-off-by: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk

km/common: remove obsolete defines and header

2011-07-27T21:44:07+00:00

These defines and the header keymile_hdlc_enet.h are obsolete
due to the removed hdlc code.

Signed-off-by: Holger Brunck 
Signed-off-by: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk

km/common: simplify debug environment

2011-07-27T21:43:33+00:00

The debug environment which is stored in textfiles in the
scripts directory was reworked. Two usecase are now present
which can be executed simply from the default environment:
run develop: this configures the environment to setup the
             rootfs via nfs
run ramfs: this configures the environment to setup the
           rootfs in ram

Each architecture now has a "arch" variable which is used
to load the architecture specific debug scripts and to set
the rootpath for NFS.

Signed-off-by: Holger Brunck 
Signed-off-by: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk

km/common: add test sw starting variable

2011-07-27T21:43:17+00:00

The test SW is started when the test_bank variable is set.

Signed-off-by: Thomas Herzmann 
Signed-off-by: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk 
Signed-off-by: Holger Brunck

km/common: rework and simplify default environment

2011-07-27T21:42:53+00:00

This is the second step to simplify and decrease the default
environment for the keymile boards. The release usecase formaly
used to set the production environment was removed and the default
configuration is now the production environment. So the formar
environment variable "release" which has done a lot of things
in the past, simply erase the current environment and do a reset
which forces u-boot to setup the default environment again.

Signed-off-by: Holger Brunck 
Signed-off-by: Valentin Longchamp 
cc: Heiko Schocher 
cc: Wolfgang Denk

arm/km: use board KM_ENV_BUS for CONFIG_I2C_ENV_EEPROM_BUS

2011-07-04T08:55:28+00:00

This is defined for all km_kirkwood boards and was not used up to now.
This value was the same for all boards but it could be changed for some
boards (and thus needs to be defined for every board).

Signed-off-by: Valentin Longchamp 
Signed-off-by: Holger Brunck 
cc: Prafulla Wadaskar 
cc: Heiko Schocher