u-boot.git/include/configs/km, branch v2013.01-rc2

km83xx: add common support for km8309 boards

2012-10-23T20:23:26Z

Add support for Keymile boards based on mpc8309 (it would be only kmvect1 for now) Signed-off-by: Gerlando Falauto [#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully] Signed-off-by: Kim Phillips

cosmetic: suvd3: align #defines

2012-10-23T20:23:25Z

Signed-off-by: Gerlando Falauto Signed-off-by: Kim Phillips

COMMON: Use __stringify() instead of xstr()

2012-10-15T18:53:47Z

Kill multiple occurances and redeclaration of xstr in favor of __stringify(). Signed-off-by: Marek Vasut Cc: Wolfgang Denk

arm/km: remove unused code

2012-09-03T12:08:54Z

For some reasons we had an own implementaion of dram_init and dram_init_banksize. This is not needed anymore, use the standard kirkwood functions instead. Signed-off-by: Holger Brunck cc: Prafulla Wadaskar cc: Valentin Longchamp cc: Gerlando Falauto Acked-By: Prafulla Wadaskar

arm/km: fix frequency of the SPI NOR Flash

2012-09-03T12:06:31Z

According to our last HW measures, this could be raised while still compatible with the potential delays on the lines. Signed-off-by: Valentin Longchamp cc: Holger Brunck Acked-By: Prafulla Wadaskar

km/arm: set SPI NOR Flash default parameters

2012-09-03T11:43:03Z

These parameters are used by the the sf probe command that are used by our update script and they therefore need to be set for all of our boards. The timing is the same as for the ENV SPI NOR Flash (since it's the same physical device) and takes the boco2 delay on the bus into account. Signed-off-by: Valentin Longchamp cc: Holger Brunck Acked-by: Prafulla Wadaskar

ARM: Remove unused stack and irq config defines

2012-09-01T12:58:22Z

CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present in most ARM board config files. IRQs are only enabled for 1 config, so remove the unused config options for IRQ and FIQ stack size as well. Cc: Albert ARIBAUD Signed-off-by: Rob Herring

Consolidate bootcount code into drivers/bootcount

2012-09-01T12:26:02Z

This patch moves all bootcount implementations into a common directory: drivers/bootcount. The generic bootcount driver is now usable not only by powerpc platforms, but others as well. Signed-off-by: Stefan Roese Cc: Heiko Schocher Cc: Valentin Longchamp Cc: Christian Riesch Cc: Manfred Rudigier Cc: Mike Frysinger Cc: Rob Herring Cc: Reinhard Meyer Tested-by: Valentin Longchamp Tested-by: Christian Riesch Acked-by: Rob Herring Acked-by: Mike Frysinger

powerpc/82xx: move km/km82xx-common.h within km82xx.h

2012-07-31T20:36:27Z

The only file including km82xx-common.h is km82xx.h. So there is no need to have it as a separate file. Signed-off-by: Gerlando Falauto

arm/km: remove calls to kw_gpio_* in board_early_init_f

2012-07-07T12:07:38Z

These functions tried to access two static tables before relocation (board_early_init_f is executed before relocation). But these static tables lie in the bss section which is not valid before relocation. These accesses then overwrote some parts of u-boot binary before it was relocated. For the kmnusa build, this results in a corrupted important env variable (bootcmd) but it may be that some other parts of the u-boot binary are corrupted. This patch solves this problem by moving all the kw_gpio_* calls to board_init, which should be early enough in the boot sequence. The only calls that could not be moved is the one for the SOFT (bitbang) I2C, and they have been replaced by a direct access to the GPIO dataout Control register to set the two GPIOs as output. Signed-off-by: Valentin Longchamp cc: Holger Brunck cc: Prafulla Wadaskar