u-boot.git/include/configs/km, branch v2014.07

kmp204x: enable the errata command

2014-05-13T15:26:55+00:00

Signed-off-by: Valentin Longchamp

kmp204x: update the CONFIG_PRAM and CONFIG_KM_RESERVED_PRAM defines

2014-05-13T15:26:55+00:00

This prevents u-boot from accessing into the reserved memory areas that
we have for /var and the logbooks.

Signed-off-by: Valentin Longchamp

kmp204x: selftest/factory test pin support

2014-05-13T15:26:55+00:00

This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
  a script by setting the active bank to testbank

The post_hotkeys_pressed return the state of the SELFTEST pin.

The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.

Finally, the unused #defines for the not so relevant mtest command are
removed.

Signed-off-by: Stefan Bigler 
Signed-off-by: Valentin Longchamp

QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and CONFIG_SYS_QE_FW_ADDR

2014-04-23T00:58:47+00:00

CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.

Signed-off-by: Zhao Qiang 
Reviewed-by: York Sun

freescale: pblimage: refactor CONFIG_SYS_FSL_PBL_{PBI, RCW}

2014-03-12T21:04:49+00:00

Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI
and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile.

Signed-off-by: Masahiro Yamada 
Cc: York Sun 
Cc: Poonam Aggrwal 
Cc: Valentin Longchamp

configs: Delete obsolete macro, CONFIG_SYS_GBL_DATA_SIZE

2014-02-19T16:10:05+00:00

CONFIG_SYS_GBL_DATA_SIZE is not used any more.
The size of struct "global_data" is automatically calculated
by asm-offsets. (See lib/asm-offsets.c)

GENERATED_GBL_DATA_SIZE should be used instead of
CONFIG_SYS_GBL_DATA_SIZE.

Signed-off-by: Masahiro Yamada

Merge branch 'master' of git://git.denx.de/u-boot-arm

2014-02-17T19:22:02+00:00

arm/km: define fdt_high env variable and allow backwards compatibility

2014-02-13T15:18:13+00:00

Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high"
This is necessary on Kirkwood so that the FDT does not get relocated
above the memory limit that the kernel cannot access
(that is the memory part reserved for the switch).
This was tested on NUSA1, where it is necessary, and on ETER1, where it
doesn't seem to hurt.

We want the scripts to also work with older versions of u-boot, where:
a) set_fdthigh is not defined (will be default env for newer u-boots)
b) the fdt will not be available

For this reason, we use "set_fdthigh" to tell whether we are running
a newer (FDT-aware) u-boot or not.
So if "set_fdthigh" runs successfully or arch != arm we try loading
the fdt; otherwise we proceed normally.

Notice how, contrary to release mode, set_fdthigh will _not_ be part of
subbootcmds for develop and ramfs, but will be executed as part of
"tftpfdt".

Since this is only needed for kirkwood cards, and it prevents the kernel
from booting on QorIQ (though it seemed to work on ETER1), we change
its definition in the default env for powerpc so that the value is only
set on ARM.

Signed-off-by: Valentin Longchamp 
Signed-off-by: Gerlando Falauto 
Signed-off-by: Holger Brunck 
Acked-by: Valentin Longchamp

arm/km: enable FDT for km_kirwkood

2014-02-13T15:17:54+00:00

This consists of:
a) Defining the addresses, enabling fdtsupport [arm]
b) Defining "cramfsloadfdt"  [arm,powerpc => common]
c) Adding the FDT address to bootm [arm,powerpc => common]
d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common]

This should work with 3.10 kernels, whether loaded through TFTP
(with rootfs either through NFS or TFTP-ramfs) or from the NAND.

The machid was left unchanged, this should keep compatibility with both
older and newer kernels.

Signed-off-by: Valentin Longchamp 
Signed-off-by: Gerlando Falauto 
Signed-off-by: Holger Brunck 
Acked-by: Valentin Longchamp

arm/km: add CONFIG_KM_BOARD_EXTRA_ENV to default environment

2014-02-13T15:17:16+00:00

This is needed for board specific additional environment variables.
E.g. the mgcoge3un has this additional "waitforne" variable.

Signed-off-by: Holger Brunck 
Acked-by: Valentin Longchamp