u-boot.git/include/configs/km, branch v2015.01

mpc85xx: inhibit qman and bman portals by default

2014-12-15T17:16:07+00:00

Not all portals might be managed and therefore visible.
Set the isdr register so that the corresponding isr register
won't be set. This is required when supporting power management.

Signed-off-by: Jeffrey Ladouceur 
Reviewed-by: York Sun

keymile/powerpc: move to the architecture-generic board system

2014-11-14T19:12:15+00:00

This converts all the Keymile powerpc boards to the generic board
initialization.

This includes the 3 Keymile powerpc subsystems: km82xx, km83xx,
and kmp204x.

Signed-off-by: Valentin Longchamp 
Reviewed-by: York Sun

mpc85xx/kmp204x: raise u-boot size to 768KB

2014-11-14T19:12:01+00:00

Until now this defined to be 512KB and the total binary size actually
was on the edge of this limit. Most of the powerpc boards have thus
moved to 768KB.

Since on the current kmp204x boards there is 1MB reserved for u-boot on
the SPI boot flash, there is no problem to set the limit to 768KB as
well to be on line with the other powerpc boards and to eventually
configure in some additional features (and binary size) to u-boot.

Signed-off-by: Valentin Longchamp 
Reviewed-by: York Sun

km_arm: convert the km_arm boards to the generic board support

2014-11-12T09:20:40+00:00

This implies that all the km_kirkwood boards and their variants now are
using the generic board init sequence.

Signed-off-by: Valentin Longchamp

kirkwood: kconfig: refactor Kconfig and defconfig

2014-08-31T01:21:21+00:00

Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").

Signed-off-by: Masahiro Yamada 
Acked-by: Prafulla Wadasdkar 
Cc: Luka Perkov

km-powerpc: define CONFIG_PRAM to protect PHRAM and PNVRAM

2014-08-20T17:44:16+00:00

When u-boot initializes the RAM (early in boot) it looks for the "pram"
env variable to know which is area it cannot use. If the "pram" env variable
is not found, the default CONFIG_PRAM value is used.

This value used to be 0 (no protection at all). This patch sets it to a
value that covers PHRAM and PNVRAM that must be protected in our case.

Signed-off-by: Valentin Longchamp 
Signed-off-by: Holger Brunck 
Reviewed-by: York Sun

kmp204x: CPU watchdog enabled

2014-08-01T21:18:34+00:00

The booting of the board is now protected by the CPU watchdog.
A failure during the boot phase will end up in board reset.

Signed-off-by: Rainer Boschung 
Reviewed-by: York Sun

kmp204x: enable the errata command

2014-05-13T15:26:55+00:00

Signed-off-by: Valentin Longchamp

kmp204x: update the CONFIG_PRAM and CONFIG_KM_RESERVED_PRAM defines

2014-05-13T15:26:55+00:00

This prevents u-boot from accessing into the reserved memory areas that
we have for /var and the logbooks.

Signed-off-by: Valentin Longchamp

kmp204x: selftest/factory test pin support

2014-05-13T15:26:55+00:00

This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
  a script by setting the active bank to testbank

The post_hotkeys_pressed return the state of the SELFTEST pin.

The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.

Finally, the unused #defines for the not so relevant mtest command are
removed.

Signed-off-by: Stefan Bigler 
Signed-off-by: Valentin Longchamp