u-boot.git/include/configs/km, branch v2015.07

Move defaults from config_cmd_default.h to Kconfig

2015-06-26T02:18:34+00:00

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger 
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini

Move default y configs out of arch/board Kconfig

2015-06-26T02:17:55+00:00

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger 
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini

net: Move the CMD_NET config to defconfigs

2015-06-01T14:40:15+00:00

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger

Move setexpr to Kconfig

2015-06-01T14:39:29+00:00

Another shell scripting command that has not been moved.

Moved using tools/moveconfig.py using these settings:

CMD_SETEXPR bool n y

Signed-off-by: Joe Hershberger 
Cc: Masahiro Yamada

nand: Remove CONFIG_MTD_NAND_VERIFY_WRITE

2015-03-31T04:24:39+00:00

The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.

Signed-off-by: Peter Tyser 
Tested-by: Heiko Schocher 
Acked-by: Heiko Schocher

mpc83xx: preempt premature board support removal by setting GENERIC_BOARD

2015-03-17T19:21:15+00:00

Boards that haven't been converted to GENERIC_BOARD does
*not* mean they should be removed.

Signed-off-by: Kim Phillips

ARM: kirkwood: move SoC headers to mach-kirkwood/include/mach

2015-02-21T13:23:52+00:00

Move arch/arm/include/asm/arch-kirkwood/*
  -> arch/arm/mach-kirkwood/include/mach/*

Signed-off-by: Masahiro Yamada 
Acked-by: Stefan Roese 
Cc: Prafulla Wadaskar 
Cc: Luka Perkov

mpc85xx: inhibit qman and bman portals by default

2014-12-15T17:16:07+00:00

Not all portals might be managed and therefore visible.
Set the isdr register so that the corresponding isr register
won't be set. This is required when supporting power management.

Signed-off-by: Jeffrey Ladouceur 
Reviewed-by: York Sun

keymile/powerpc: move to the architecture-generic board system

2014-11-14T19:12:15+00:00

This converts all the Keymile powerpc boards to the generic board
initialization.

This includes the 3 Keymile powerpc subsystems: km82xx, km83xx,
and kmp204x.

Signed-off-by: Valentin Longchamp 
Reviewed-by: York Sun

mpc85xx/kmp204x: raise u-boot size to 768KB

2014-11-14T19:12:01+00:00

Until now this defined to be 512KB and the total binary size actually
was on the edge of this limit. Most of the powerpc boards have thus
moved to 768KB.

Since on the current kmp204x boards there is 1MB reserved for u-boot on
the SPI boot flash, there is no problem to set the limit to 768KB as
well to be on line with the other powerpc boards and to eventually
configure in some additional features (and binary size) to u-boot.

Signed-off-by: Valentin Longchamp 
Reviewed-by: York Sun