u-boot.git/include/configs/km, branch v2020.01

env: Finish migration of common ENV options

2019-11-20T23:32:09+00:00

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk 
Cc: Joe Hershberger 
Cc: Patrick Delaunay 
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini 
Acked-by: Joe Hershberger 
Reviewed-by: Simon Goldschmidt

env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND check

2019-11-20T23:31:24+00:00

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it.  We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result.  The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED.  This seems like the most likely use, historically, of
the variable, but it was not used.  Add logic to check for this now.

Cc: Wolfgang Denk 
Cc: Joe Hershberger 
Signed-off-by: Tom Rini 
Reviewed-by: Simon Glass 
Acked-by: Joe Hershberger

defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENT

2019-11-12T16:08:00+00:00

Move this symbol to Kconfig.  As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.

Signed-off-by: Tom Rini

Convert CONFIG_ARCH_CPU_INIT to Kconfig

2019-08-25T23:32:55+00:00

This converts the following to Kconfig:
   CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford 
Acked-by: Chris Packham 
Tested-by: Felix Brack

powerpc/km: remove unmaintained board KMLION1

2019-08-12T07:12:38+00:00

This board is unmaintained and can be removed. This also allows us to
remove kmp204x-common.h and integrate it in kmp204x.h.

Signed-off-by: Valentin Longchamp 
Signed-off-by: Holger Brunck 
Signed-off-by: Stefan Roese

km/rgmii: port Ethernet interface of KM Kirkwood boards to driver model

2019-08-12T07:12:38+00:00

Activate the driver model for the Ethernet interface (RGMII) in the KM
Kirkwood Kconfig file. Additionally, raise the auto negotiation timeout
to eight seconds as more time is required for those boards.

Signed-off-by: Pascal Linder 
Signed-off-by: Holger Brunck 
Signed-off-by: Stefan Roese

km/uart: port UART interface of KM Kirkwood boards to driver model

2019-08-12T07:12:38+00:00

Activate the driver model for the serial interface in the KM Kirkwood
Kconfig file. The associated preprocessor definitions could be removed
from the header file. However, the clock of 200 MHz needs to be declared
in the device tree.

Signed-off-by: Pascal Linder 
Signed-off-by: Holger Brunck 
Signed-off-by: Stefan Roese

km: clean up header files for KM Kirkwood boards

2019-08-12T07:12:38+00:00

Remove unused preprocessor definitions and comments of already eliminated
code.

The Ethernet driver configuration is already declared in
arch/arm/mach-kirkwood/include/mach/config.h and, therefore, superfluous.

Signed-off-by: Pascal Linder 
Signed-off-by: Holger Brunck 
Signed-off-by: Stefan Roese

km: remove obsolete definitions in KM header files

2019-08-12T07:12:38+00:00

After moving the KM specific configurations to Kconfig, the associated
preprocessor definitions can now be removed in the headers. Moreover, the
whitelist has been adapted correspondingly.

Signed-off-by: Pascal Linder 
Signed-off-by: Holger Brunck 
Signed-off-by: Stefan Roese

km: add Kconfig menus for KM boards

2019-08-12T07:12:38+00:00

To execute the conversion away from board specific header files, Kconfig
menus have been implemented for all KM boards and additionally for those
having an ARM architecture.

For the moment, the preprocessor definitions stay in the headers. The
boolean types, however, needed a modification (#define CONFIG_* 1).

The default configuration files of some boards required an update in order
to not change the currently defined values of the configurations.

Signed-off-by: Pascal Linder 
Signed-off-by: Holger Brunck 
Signed-off-by: Stefan Roese