u-boot.git/include/configs/maxbcm.h, branch v2016.09

spl: Remove unused CONFIG_SPL_SPI_* definitions

2016-08-26T06:33:34+00:00

As of commit 88e34e5 ("spl: replace CONFIG_SPL_SPI_* with
CONFIG_SF_DEFAULT_*") these defines are not used. Remove them to avoid
confusion.

Signed-off-by: Chris Packham 
Signed-off-by: Stefan Roese

configs: Re-sync almost all of cmd/Kconfig

2016-04-25T19:09:40+00:00

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND.  Due to how we have used this historically
we need to take further care here when converting.

Signed-off-by: Tom Rini

arm: mvebu: Move SoC selection (A38X vs AXP) into Kconfig

2016-01-14T13:08:59+00:00

Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.

Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.

And CONFIG_DDR3 is removed, as its not referenced anywhere.

Signed-off-by: Stefan Roese 
Cc: Luka Perkov

arm: mvebu: Make ECC support configurable on Armada XP

2016-01-14T13:08:59+00:00

Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.

Signed-off-by: Stefan Roese 
Cc: Luka Perkov 
Cc: Phil Sutter

arm: mvebu: Move some defines to common include file

2016-01-14T13:08:59+00:00

This patch moves some config options to the mvebu common include file.
Making it easier to not forget these defines for new boards.

Signed-off-by: Stefan Roese 
Cc: Luka Perkov 
Cc: Dirk Eibach

net: mvneta: Convert to driver model

2016-01-14T13:08:59+00:00

Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.

With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:

PHY-mode ("phy-mode") and PHY-address ("reg").

The base addresses for the ethernet controllers can be removed from
the header files as well.

Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.

Signed-off-by: Stefan Roese 
Cc: Luka Perkov 
Cc: Dirk Eibach 
Cc: Joe Hershberger 
Cc: Simon Glass

arm: mvebu: Add DM and OF_CONTROL support to SPL

2016-01-14T13:08:59+00:00

This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.

This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.

Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:

   arch/arm/cpu/u-boot-spl.lds

This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.

Signed-off-by: Stefan Roese 
Cc: Luka Perkov 
Cc: Dirk Eibach 
Cc: Simon Glass

sf: Move SPI flash drivers to defconfig

2015-11-25T15:06:05+00:00

There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.

Signed-off-by: Bin Meng

arm, powerpc: select SYS_GENERIC_BOARD

2015-10-24T17:50:38+00:00

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada

arm: mvebu: Only set CONFIG_SKIP_LOWLEVEL_INIT for SPL

2015-10-21T00:25:00+00:00

When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.

Signed-off-by: Stefan Roese