This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

XILINX_SPI_FLASH_BASEADDR logic has been converted to DM that's why
there is no reason to depend on this address anymore.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.

GPIO reset is handled via sysreset with adding this fragment to DT.

gpio-restart {
	compatible = "gpio-restart";
	gpios = <&reset_gpio 0 0 0>;
	/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};

hard-reset-gpio property is not documented and also handled.
Conversion is required.

Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

These macros are not required anymore. These will be taken from
configuration file.

Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every
use is couched by __stringify(...).

Hence, convert it to a proper string option.

Signed-off-by: Mario Six <mario.six@gdsys.cc>