u-boot.git/include/configs/microblaze-generic.h, branch v2019.07

Convert CONFIG_ENV_SPI_* to Kconfig

2019-03-25T21:36:59Z

This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay

Convert CONFIG_SF_DEFAULT_* to Kconfig

2019-03-25T21:36:53Z

This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

2018-10-19T23:19:50Z

This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford [trini: Re-migrate] Signed-off-by: Tom Rini

Convert CONFIG_MII et al to Kconfig

2018-08-17T17:03:54Z

This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford Acked-by: Jagan Teki Acked-by: Joe Hershberger

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

2018-07-22T23:20:17Z

This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford

microblaze: Remove XILINX_SPI_FLASH_BASEADDR logic

2018-07-19T08:49:56Z

XILINX_SPI_FLASH_BASEADDR logic has been converted to DM that's why there is no reason to depend on this address anymore. Signed-off-by: Michal Simek

microblaze: Convert generic platform to DM gpio

2018-07-19T08:49:55Z

Converting GPIO to DM requires to do changes in reset subsystem that's why support for Microblaze soft reset via sysreset and GPIO sysreset support was added. These two patches enables enabling GPIO DM. Microblaze soft reset is bind at last reset method. GPIO reset is handled via sysreset with adding this fragment to DT. gpio-restart { compatible = "gpio-restart"; gpios = <&reset_gpio 0 0 0>; /* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */ }; hard-reset-gpio property is not documented and also handled. Conversion is required. Unfortunately do_reset is required for SPL that's why use only soft microblaze reset for now. Signed-off-by: Michal Simek

microblaze: Delete Xilinx watchdog related macros

2018-07-19T08:49:55Z

These macros are not required anymore. These will be taken from configuration file. Signed-off-by: Shreenidhi Shedi Signed-off-by: Michal Simek

microblaze: Cosmetic changes in Microblaze related files

2018-07-19T08:49:55Z

Signed-off-by: Shreenidhi Shedi Signed-off-by: Michal Simek

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12Z

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini