u-boot.git/include/configs/mx28evk.h, branch v2013.10-rc2

Merge git://git.denx.de/u-boot-arm

2013-07-31T09:30:38Z

Conflicts: board/freescale/mx6qsabrelite/Makefile board/freescale/mx6qsabrelite/mx6qsabrelite.c include/configs/mx6qsabrelite.h Signed-off-by: Stefano Babic

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38Z

Signed-off-by: Wolfgang Denk [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini

ARM: mxs: Consolidate configuration options

2013-07-24T10:59:57Z

Pull all the duplicate configuration options into configs/mxs.h from the board configuration files. This reduces the files greatly and makes them somewhat more readable. Besides, we do no longer have such a horrible duplication of code. Note that the mx23evk grew in size slightly. This is due to the CONFIG_SYS_CBSIZE now being set to 1024 as it is on the rest of MXS systems. This patch also fixes the OCRAM size for i.MX23. The i.MX23 has only 32kB of OCRAM, while i.MX28 has 128kB of OCRAM. I verified the configuration didn't change for each of the boards, but I didn't boot-test it on the boards I do not have. I configured U-Boot for each board using the "make ... _config" command and then ran "cpp -I include -dM include/config.h" , which dumped all the configuration options. I did this both before and after this patch and finally compared the results for each MXS board. Actually, the results do differ slightly, since the configs/mxs.h file now properly includes the correct iomux-mx23.h or iomux-mx28.h , so while comparing, I had to ignore these new defines. These have no impact on U-Boot configuration though. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Lauri Hintsala Cc: Otavio Salvador Cc: Stefano Babic

mx28evk: Add splash screen support

2013-05-16T15:44:46Z

Enable display support. Signed-off-by: Fabio Estevam

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

2013-05-11T07:25:36Z

Conflicts: drivers/mtd/nand/mxc_nand_spl.c include/configs/m28evk.h

mx28evk: Guard NAND-related ENV defines with CONFIG_ENV_IS_IN_NAND

2013-05-01T20:41:10Z

The redundancy related defines are only correct for NAND, so guard all of that area with CONFIG_ENV_IS_IN_NAND Cc: Fabio Estevam Signed-off-by: Tom Rini

mx28evk: add trimffs to nand command

2013-04-16T16:58:47Z

this is usefull when writing an UBI image which contains and UBIFS volume (check README.nand and UBI FAQ for more details) Signed-off-by: Eric Bénard Acked-by: Otavio Salvador

mx28evk: Introduce a new target for saving env vars to NAND

2013-04-03T08:55:18Z

Introduce 'mx28evk_nand' target for saving environment variables into NAND. The mx28evk board does not come with a NAND flash populated from the factory. It comes with an empty slot (U23), which allows the insertion of a 48-pin TSOP flash device. Tested with a K9LBG08U0D. Signed-off-by: Fabio Estevam Reviewed-by: Otavio Salvador

mx28evk: Disable CONFIG_CMD_I2C

2013-03-20T10:40:58Z

When loading a Freescale 2.6.35 on a mx28evk the following issue is seen: sgtl5000_hw_read: read reg error : Reg 0x00 Device with ID register 0 is not a SGTL5000 Disabling CONFIG_CMD_I2C makes the sgtl5000 probe to succeed. Mainline kernel does not show this problem. Until the real cause is not identified, disable 'CONFIG_CMD_I2C' for the time being. Signed-off-by: Fabio Estevam

configs: mx28evk: Use single-line comments

2013-03-20T10:28:51Z

No need to use multi-line style comments for single-line contents. Signed-off-by: Fabio Estevam Reviewed-by: Otavio Salvador