u-boot.git/include/configs/mx31ads.h, branch v2011.03

Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

2010-10-26T19:05:30+00:00

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new  file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk 
Acked-by: Kumar Gala

MXC: Correct SPI_CPOL setting in SPI driver

2010-09-30T12:42:13+00:00

The handling of the SPI_CPOL bit inside the SPI
driver was wrong. As reported by the manual,
the meaning of the SSPOL inside the
configuration register is the same as reported
by SPI specification (0 if low in idle, 1 is high
on idle). The driver inverts this logic.

Because this patch sets the logic as specified, it is required
to clear the CPOL bit in the configuration file to adapt
to the correct logic.

Signed-off-by: Stefano Babic 
Signed-off-by: David Jander

MX: RTC13783 uses general function to access PMIC

2010-05-05T07:48:41+00:00

The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.

Signed-off-by: Stefano Babic 
Tested-by: Magnus Lilja

Convert CS8900 Ethernet driver to CONFIG_NET_MULTI API

2009-08-25T20:35:54+00:00

All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
  - changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
  - changed CS8900_BASE to CONFIG_CS8900_BASE
  - changed CS8900_BUS?? to CONFIG_CS8900_BUS??
  - cleaned up line lengths
  - modified VCMA9 command function that accesses the device
  - removed MAC address initialization from lib_arm/board.c

Signed-off-by: Ben Warren 
Tested-by: Wolfgang Denk 
Acked-by: Wolfgang Denk

serial_mx31: allow it to work with mx27 too and rename to serial_mxc

2009-06-21T14:18:13+00:00

UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.

Signed-off-by: Ilya Yanok

Separate mtdparts command from jffs2

2009-03-20T21:39:14+00:00

Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese 
Signed-off-by: Kyungmin Park

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

i.MX31: switch to CFG_HZ=1000

2008-10-08T16:59:02+00:00

Switch to the standard CFG_HZ=1000 value, while at it, minor white-space
cleanup, remove CFG_CLKS_IN_HZ from config-headers. Tested on mx31ads,
provides 2% or 0.4% precision depending on the
CONFIG_MX31_TIMER_HIGH_PRECISION flag. Measured with stop-watch on 100s
boot-delay.

Signed-off-by: Guennadi Liakhovetski

Merge branch 'Makefile-next' of git://git.denx.de/u-boot-arm

2008-09-12T14:13:12+00:00

i.MX31: Make the SPI bus and chip select configurable for MC13783

2008-09-11T23:23:44+00:00

The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.

This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.

Signed-off-by: Magnus Lilja