u-boot.git/include/configs/mx31ads.h, branch v2012.04

MX: serial_mxc: cleanup removing nasty #ifdef

2011-12-06T22:59:40+00:00

The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS__
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.

Signed-off-by: Stefano Babic 
CC: Marek Vasut 
CC: Wolfgang Denk 
CC: Fabio Estevam 
CC: Helmut Raiger 
CC: John Rigby 
CC: Matthias Weisser 
CC: Jason Liu 
Acked-by: Jason Liu

rtc: Make mc13783-rtc driver generic

2011-11-03T21:56:19+00:00

Rename mc13783-rtc so that it can be used for both MC13783 and MC13892 PMICs.

efikamx board, for example, does use a MC13892 PMIC, but the RTC selection is currently made as:

#define CONFIG_RTC_MC13783

,which is not very obvious.

Let the MC13783 and MC13892 RTC be selected by:

#define CONFIG_RTC_MC13XXX

Signed-off-by: Fabio Estevam 
Acked-by: Stefano Babic

MX31: mx31ads: use new pmic driver

2011-10-27T19:56:32+00:00

Switch to new pmic generic driver.

Signed-off-by: Stefano Babic 
CC: Fabio Estevam

board configs: drop NET_MULTI references

2011-10-05T20:22:16+00:00

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger

mx31ads: Place machine ID into board config

2011-09-30T20:01:04+00:00

Let common code set the machine ID.

Signed-off-by: Fabio Estevam

MX31: mx31ads: make use of GPIO framework

2011-09-04T09:36:12+00:00

Signed-off-by: Stefano Babic

mx31ads: Fix environment location on flash

2011-06-07T13:05:48+00:00

At the moment u-boot and u-boot environment on flash
have overlapping addresses, so each u-boot update erases
the environment. Fix this by placing evironment right
after u-boot. Also, remove confusing comment about environment
location.

Signed-off-by: Felix Radensky

mx31ads: Use the new relocation scheme

2011-06-06T07:35:25+00:00

This fixes the MX31ADS build by using the new relocation scheme.

Signed-off-by: Fabio Estevam 
Tested-by: Felix Radensky

IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers

2011-04-27T17:38:05+00:00

As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic

Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

2010-10-26T19:05:30+00:00

CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new  file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk 
Acked-by: Kumar Gala