u-boot.git/include/configs/mx31ads.h, branch v2012.07

CONFIG_SYS_BAUDRATE_TABLE: Add , place there

2012-06-20T18:26:16+00:00

We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in  which mkconfig places after  in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini

MX: serial_mxc: cleanup removing nasty #ifdef

2011-12-06T22:59:40+00:00

The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS__
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.

Signed-off-by: Stefano Babic 
CC: Marek Vasut 
CC: Wolfgang Denk 
CC: Fabio Estevam 
CC: Helmut Raiger 
CC: John Rigby 
CC: Matthias Weisser 
CC: Jason Liu 
Acked-by: Jason Liu

rtc: Make mc13783-rtc driver generic

2011-11-03T21:56:19+00:00

Rename mc13783-rtc so that it can be used for both MC13783 and MC13892 PMICs.

efikamx board, for example, does use a MC13892 PMIC, but the RTC selection is currently made as:

#define CONFIG_RTC_MC13783

,which is not very obvious.

Let the MC13783 and MC13892 RTC be selected by:

#define CONFIG_RTC_MC13XXX

Signed-off-by: Fabio Estevam 
Acked-by: Stefano Babic

MX31: mx31ads: use new pmic driver

2011-10-27T19:56:32+00:00

Switch to new pmic generic driver.

Signed-off-by: Stefano Babic 
CC: Fabio Estevam

board configs: drop NET_MULTI references

2011-10-05T20:22:16+00:00

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger

mx31ads: Place machine ID into board config

2011-09-30T20:01:04+00:00

Let common code set the machine ID.

Signed-off-by: Fabio Estevam

MX31: mx31ads: make use of GPIO framework

2011-09-04T09:36:12+00:00

Signed-off-by: Stefano Babic

mx31ads: Fix environment location on flash

2011-06-07T13:05:48+00:00

At the moment u-boot and u-boot environment on flash
have overlapping addresses, so each u-boot update erases
the environment. Fix this by placing evironment right
after u-boot. Also, remove confusing comment about environment
location.

Signed-off-by: Felix Radensky

mx31ads: Use the new relocation scheme

2011-06-06T07:35:25+00:00

This fixes the MX31ADS build by using the new relocation scheme.

Signed-off-by: Fabio Estevam 
Tested-by: Felix Radensky

IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers

2011-04-27T17:38:05+00:00

As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic