The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>

According to include/i2c.h:

"/*
 * Many boards/controllers/drivers don't support an I2C slave interface so
 * provide a default slave address for them for use in common code.  A real
 * value for CONFIG_SYS_I2C_SLAVE should be defined for any board which does
 * support a slave interface.
 */
#ifndef	CONFIG_SYS_I2C_SLAVE
#define	CONFIG_SYS_I2C_SLAVE	0xfe
#endif
"

As the mxc_i2c driver does not support slave mode, there is no need
to define CONFIG_SYS_I2C_SLAVE in i.MX board file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>

We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini <trini@ti.com>

CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Helmut Raiger <helmut.raiger@hale.at>
CC: John Rigby <jcrigby@gmail.com>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>

No board information is passed for MX53SMD, so remove get_board_rev function.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Let common code set the machine ID.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>