u-boot.git/include/configs/mx6qsabreauto.h, branch master

mx6sabreauto: Update to SPL only mode

2017-07-12T07:44:22+00:00

As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.

This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.

Signed-off-by: Vanessa Maegima 
Reviewed-by: Fabio Estevam 
Reviewed-by: Stefano Babic

mx6qsabreauto: Add SPL support

2017-07-12T07:44:22+00:00

Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.

Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg

Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg

Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg

Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.

Signed-off-by: Vanessa Maegima 
Reviewed-by: Fabio Estevam 
Reviewed-by: Stefano Babic

Kconfig: USB: Migrate existing USB_EHCI_xxx options

2017-05-15T17:00:26+00:00

The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC

This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.

Cc: Marek Vasut 
Signed-off-by: Tom Rini 
Reviewed-by: Marek Vasut

Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to Kconfig

2017-05-15T17:00:21+00:00

Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled.  In some
cases we had not already migrated to CONFIG_USB so do that as well.

Cc: Marek Vasut 
Signed-off-by: Tom Rini 
Reviewed-by: Marek Vasut

Kconfig: USB: Migrate CONFIG_USB_EHCI to CONFIG_USB_EHCI_HCD

2017-05-15T14:40:05+00:00

In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.

Cc: Marek Vasut 
Signed-off-by: Tom Rini 
Reviewed-by: Marek Vasut

flash: complete CONFIG_SYS_NO_FLASH move with renaming

2017-02-12T19:30:25+00:00

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada

mx6qsabreauto: Pass the correct parallel NOR width

2017-01-27T09:30:53+00:00

On mx6qsabreauto the parallel NOR width is 16 bits, so pass configure
CONFIG_SYS_FLASH_CFI_WIDTH correctly so that the CFI driver does not
use 8 bits by default.

Signed-off-by: Fabio Estevam

config: Drop CONFIG_CONSOLE_DEV

2016-10-23T22:33:36+00:00

This is not really a config. Rename it to avoid confusion.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini 
Reviewed-by: Jagan Teki

configs: Migrate CONFIG_USB_STORAGE

2016-09-09T18:59:35+00:00

In some cases we were missing CONFIG_USB=y so enable that when needed.

Reviewed-by: Masahiro Yamada 
Signed-off-by: Tom Rini

mx6qsabreauto: Avoid hardcoded RAM size

2016-07-12T15:58:48+00:00

Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.

Signed-off-by: Vanessa Maegima 
Acked-by: Fabio Estevam