The U-Boot port runs on a variety of RPi models, not just the B. So,
rename the port to something slightly more generic.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

Detect the board revision early during boot, and print the decoded
model name.

Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
  board so only host mode makes sense. Others connect the SoC directly
  to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
  although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
  the environment there. Other models use an SD card and so don't support
  saving the environment (unless we store it in a file on the FAT boot
  partition...)

Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>

CONFIG_ARM1176 is defined for some boards but not referenced at all.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

USB support must be enabled before config_distro_bootcmd.h is included
for bootcmd to include USB-related functionality.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

The built-in SMSC 95xx chip doesn't know its own MAC address. Instead,
we must query it from the VC firmware; it's probably encoded in fuses
on the BCM2835.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

Enable DWC2 USB, storage and ethernet support. Tested on RPi B+.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h, after which this part of
rpi_b.h was modelled.

The #defines to enable/disable U-Boot commands/features were moved
earlier in rpi_b.h, so they are set up before config_distro_bootcmd.h
is included, since it tests whether certain features should be included
based on those defines.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

Use the new option -r for env import.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>