This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well.  Remove it.

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>

There is no real need to exactly define space for saving patterns for
alternate memory test. It is much easier to allocate space on the stack and
use it instead of trying to find out space where pattern should be saved.

For example if you want to test the whole DDR memory you can't save patter
to DDR and you need to find it out. On Xilinx devices DDR or OCM addresses
were chosen but that means that OCM needs to be mapped and U-Boot has
access permission there.

It is easier to remove this limitation and simply save it on stack because
it is very clear that memory test can't rewrite U-Boot and U-Boot has also
full access to memory where runs from.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

This converts the following to Kconfig:
   CONFIG_PHYLIB
   CONFIG_BITBANGMII
   CONFIG_MV88E6352_SWITCH
   CONFIG_MV88E61XX_SWITCH
   CONFIG_PHYLIB_10G
   CONFIG_PHY_AQUANTIA
   CONFIG_PHY_ATHEROS
   CONFIG_PHY_BROADCOM
   CONFIG_PHY_CORTINA
   CONFIG_PHY_DAVICOM
   CONFIG_PHY_ET1011C
   CONFIG_PHY_LXT
   CONFIG_PHY_MARVELL
   CONFIG_PHY_MICREL
   CONFIG_PHY_NATSEMI
   CONFIG_PHY_REALTEK
   CONFIG_RTL8211X_PHY_FORCE_MASTER
   CONFIG_PHY_SMSC
   CONFIG_PHY_TERANETICS
   CONFIG_PHY_TI
   CONFIG_PHY_VITESSE
   CONFIG_PHY_XILINX

Signed-off-by: Tom Rini <trini@konsulko.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it.  We have one
board where we can simply multiple CONFIG_ENV_SIZE by two for the same
result.  The other place where we could but were not previously using
this is for where env_internal.h checks for if we should set
ENV_IS_EMBEDDED.  This seems like the most likely use, historically, of
the variable, but it was not used.  Add logic to check for this now.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This converts the following to Kconfig:
   CONFIG_SHOW_BOOT_PROGRESS

Signed-off-by: Simon Glass <sjg@chromium.org>

Now that various SPI related options depend on CONFIG_DEPRECATED, in
order for platforms to build out of the box they need to disable various
other options.

Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2,
while the old SH parts use CONFIG_SYS_CLK_FREQ directly.
Just put this into the TMU implementation and drop the
CONFIG_SH_TMU_CLK_FREQ config option.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>