Most device headers contain SoC specific part and common Tegra post part.
Add a generic header which can be used by any Tegra device of one of the
supported SoC generations (T20, T30, T114, T124 or T210) without need in
device specific configuration.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>

Convert CFG_TEGRA_BOARD_STRING into Kconfig option and move it into device
board Kconfig.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>

Link CFG_SYS_NS16550_COM1 value to chosen CONFIG_TEGRA_ENABLE_UART Tegra
wide. Remove all CFG_SYS_NS16550_COM1 from device headers.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>

Perform a simple rename of CONFIG_TEGRA_BOARD_STRING to CFG_TEGRA_BOARD_STRING

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_TEGRA_ENABLE_UARTA
   CONFIG_TEGRA_ENABLE_UARTB
   CONFIG_TEGRA_ENABLE_UARTC
   CONFIG_TEGRA_ENABLE_UARTD
   CONFIG_TEGRA_SPI
   CONFIG_TEGRA_UARTA_GPU
   CONFIG_TEGRA_UARTA_SDIO1
   CONFIG_TEGRA_VDD_CORE_TPS62361B_SET3
   CONFIG_TEGRA_VDD_CORE_TPS62366A_SET1

Signed-off-by: Tom Rini <trini@konsulko.com>

This removes the following unreferenced CONFIG symbols:
   CONFIG_FDTADDR
   CONFIG_FDTFILE
   CONFIG_FLASH_SECTOR_SIZE
   CONFIG_FSL_CPLD
   CONFIG_HDMI_ENCODER_I2C_ADDR
   CONFIG_I2C_MVTWSI
   CONFIG_I2C_RTC_ADDR
   CONFIG_IRAM_END
   CONFIG_IRAM_SIZE
   CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
   CONFIG_L1_INIT_RAM
   CONFIG_MACB_SEARCH_PHY
   CONFIG_MIU_2BIT_21_7_INTERLEAVED
   CONFIG_MTD_NAND_VERIFY_WRITE
   CONFIG_MVGBE_PORTS
   CONFIG_NETDEV
   CONFIG_NUM_DSP_CPUS
   CONFIG_PHY_BASE_ADR
   CONFIG_PHY_INTERFACE_MODE
   CONFIG_PSRAM_SCFG
   CONFIG_RAMBOOT_SPIFLASH
   CONFIG_RAMBOOT_TEXT_BASE
   CONFIG_RD_LVL
   CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
   CONFIG_SETUP_INITRD_TAG
   CONFIG_SH_QSPI_BASE
   CONFIG_SMDK5420
   CONFIG_SOCRATES
   CONFIG_SPI_ADDR
   CONFIG_SPI_FLASH_QUAD
   CONFIG_SPI_FLASH_SIZE
   CONFIG_SPI_HALF_DUPLEX
   CONFIG_SPI_N25Q256A_RESET
   CONFIG_TEGRA_SLINK_CTRLS
   CONFIG_TPM_TIS_BASE_ADDRESS
   CONFIG_UBOOT_SECTOR_COUNT
   CONFIG_UBOOT_SECTOR_START
   CONFIG_VAR_SIZE_SPL
   CONFIG_VERY_BIG_RAM

And also:
   BL1_SIZE
   PHY_NO
   RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support.  A large number of platforms had enabled
support but never supported a kernel so old as to require it.  Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years.  This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user.  When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts.  In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_MMC_ENV_DEV
   CONFIG_SYS_MMC_ENV_PART

Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.

Signed-off-by: Tom Rini <trini@konsulko.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>