u-boot.git/include/configs/ten64.h, branch master

configs: Remove duplicate newlines

2024-07-05T19:57:01+00:00

Drop all duplicate newlines from config headers.
No functional change.

Signed-off-by: Marek Vasut

board: ten64: add a bootmenu entries for NAND-based entries

2023-08-03T13:40:50+00:00

The recovery-firmware and OpenWrt-NAND do not yet have bootflow
/bootstd entrypoints, so add bootmenu entries to make them
accessible.

Signed-off-by: Mathew McBride 
Reviewed-by: Peng Fan

board: traverse: ten64: add NAND based OpenWrt bootcmd

2023-08-03T13:40:50+00:00

The default Ten64 MTD configuration reserves two ubifs partitions
for OpenWrt residing on NAND flash. Add the bootcmd for this system
into the default environment.

Signed-off-by: Mathew McBride 
Reviewed-by: Peng Fan

board: traverse: ten64: specify bootargs for recovery environment

2023-08-03T13:40:50+00:00

The recovery environment[1] on the Ten64 is a OpenWrt-
based ramdisk stored on the NAND intended to help with
system setup tasks.

Before the bootargs were not being set for the recovery
command, relying instead on the existing bootargs variable.

Ensure the bootargs are set correctly prior to booting recovery.

Signed-off-by: Mathew McBride 

[1] https://ten64doc.traverse.com.au/software/recovery/

Reviewed-by: Peng Fan

board: traverse: ten64: update DPAA2 (network) binary path on sdcards

2023-08-03T13:40:50+00:00

Change the firmware on microSD path to "firmware/traverse/ten64"
as per EBBR section 4.2[1].

The Traverse firmware tools now locate the DPAA2 firmware
and configuration files under that path on the rescue
SD card image.
If a user then installs a standard Linux
distribution over the top of that sdcard, (in theory)
it will be left alone by distribution boot tooling.

Signed-off-by: Mathew McBride 

[1] https://arm-software.github.io/ebbr/index.html#firmware-partition-filesystem

Reviewed-by: Peng Fan

board: traverse: ten64: fix DPAA2 (network) DPL corruption issue

2023-08-03T13:40:50+00:00

The DPAA2 DPL (data plane layout) file was previously
being loaded into 0x80300000, and set to be applied
just before hand off to the kernel.

When a FIT image with a load_address of 0x80000000 was
booted with bootm, the DPL in memory was overwritten.

Move the DPL load to 0x8E000000 (196MiB away from 0x80000000,
and below the other typical load addr of 0x90000000).

Ideally in the future, the DPL lazyapply command
("fsl_mc lazyapply DPL $dpl_addr") should be set to
load the DPL contents into a memory area owned by U-Boot.

Signed-off-by: Mathew McBride 
Reviewed-by: Peng Fan

global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFG

2022-12-23T15:09:42+00:00

Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS

Signed-off-by: Tom Rini

global: Move remaining CONFIG_SYS_* to CFG_SYS_*

2022-12-05T21:06:08+00:00

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.

Signed-off-by: Tom Rini 
Reviewed-by: Simon Glass

include/configs: drop COUNTER_FREQUENCY

2022-04-21T19:27:17+00:00

Since we have CONFIG_COUNTER_FREQUENCY enabled, no need COUNTER_FREQUENCY

Signed-off-by: Peng Fan

Convert CONFIG_DIMM_SLOTS_PER_CTLR to Kconfig

2022-04-08T14:46:22+00:00

This converts the following to Kconfig:
   CONFIG_DIMM_SLOTS_PER_CTLR

Signed-off-by: Tom Rini