Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>

When calling board_late_init, we need to define CONFIG_BOARD_LATE_INIT.
The latest ecovec config defines BOARD_LATE_INIT, board_late_init is not called.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Wolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-arm:
  ARM926EJS: Fix cache.c to comply with checkpatch.pl
  ARM926EJS: Make asm routines volatile in cache ops
  MX35: mx35pdk: wrong board revision
  ARM1136: MX35: Make asm routines volatile in cache ops
  ARM: add u-boot.imx as target for i.MX SOCs
  M28: Pull out CONFIG_APBH_DMA so it's always enabled
  DMA: Split the APBH DMA init into block and channel init
  imx: Return gpio_set_value in gpio_direction_output
  imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5)
  imx: Add GPIO_TO_PORT macro in the mxc_gpio driver
  imx: Remove unneeded/repititive definitions from imx headers
  i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
  MX31: mx31pdk: drop enable_caches from board file
  i.MX28: Fix initial stack pointer position
  mx35: mx35pdk: fix when cache functions are linked
  mx35: flea3: fix when cache functions are linked
  ARM: 926ejs: use debug() for misaligned addresses
  ARM1136: add cache flush and invalidate operations
  mx6qsabrelite: Fix the serial console port
  mx6qsabrelite: Add boot switch setting information into the README
  i.MX6: mx6qsabrelite: add cache commands if cache is enabled
  i.MX6: implement enable_caches()
  i.MX6: define CACHELINE_SIZE
  MX53: DDR: Fix ZQHWCTRL field TZQ_CS
  mx28evk: Add a README file
  mx28: Split the README into a common part and a m28 specific part
  tricorder: Load kernel from ubifs
  tricorder: Add UBIFS
  cm-t35: fix Ethernet reset timing
  hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
  BeagleBoard: Remove userbutton command and use gpio command instead
  OMAP: Move omap1510inn to Unmaintained / Orphaned

The board revision is detected accessing to the pmic,
that is not available before relocation (I2C).
This generates the following error:

CPU:   Freescale i.MX35 rev 2.0 at 532 MHz.
Reset cause: WDOG
<reg num> = 7 is invalid. Should be less than 0
Board: MX35 PDK 1.0

The revision number is wrong, as a default value is printed
(tested on a mx35pdk Rev. 2.0).

Move the output in the board_late_init(), when
pmic can be accessed.

Signed-off-by: Stefano Babic <sbabic@denx.de>

The ABPH DMA is now used also by the SD card. Therefore it has to be enabled
even if NAND is disabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>

The patch:

  m28evk: Use GENERATED_GBL_DATA_SIZE
  commit 1084606c972ea5f1d89f69bdbd978b867d0ee521

introduced usage of GENERATED_GBL_DATA_SIZE and calculation of initial stack
pointer position defived from that. Due to a small typo, the SP position moved
to 0x21f80, which is past the SRAM area. This didn't manifest on the real
hardware as the SRAM repeats there (address bits in the CPU being ignored).

Though this was caught in QEMU, where it crashed the emulator.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Stefano Babic <sbabic@denx.de>

On mx6qsabrelite the console is ttymxc1.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>