Commit 69434e4c deleted spieval board support
but it missed to clean up include/configs/spieval.h file.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Sandbox uses an emulated memory map which is quite small. We don't need the
CONFIG_PHYS_64BIT option since we can address memory with a 32-bit offset
into our ram_buf.

Adjust the phys_addr_t and phys_size_t types accordingly.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>

This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.

1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
   other ecc-schemes also supported in hardware. like;
 - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
   the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
   software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
 - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
   supports BCH16 ecc-scheme also.

2) Different platforms use different CONFIG_xx to select ecc-schemes, which
   adds confusion for user while migrating platforms.
 - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
    8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
    whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
    and BCH16 (in future).
 - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
    correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
 - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library

Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)

Signed-off-by: Pekon Gupta <pekon@ti.com>

ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
	and include in all board configs using AM33xx SoC platform.

Signed-off-by: Pekon Gupta <pekon@ti.com>

Defines constants required to support 8K page size NAND flash.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

nand_ecclayout is present in mtd.h at Linux.
Move this structure to mtd.h to comply with Linux.

Also, increase the ecc placement locations to 640 to suport device having
writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone
up to 640 bytes and consequently the maximum ecc placement locations have
also gone up to 640.

Changes from Prabhabkar's version (squashed into one patch to preserve
bisectability):
 - Added _LARGE to MTD_MAX_*_ENTRIES

   This makes the names match current Linux source, and resolves
   a conflict between
   http://patchwork.ozlabs.org/patch/280488/
   and
   http://patchwork.ozlabs.org/patch/284513/

   The former was posted first and is closer to matching Linux, but
   unlike Linux it does not add _LARGE to the names.  The second adds
   _LARGE to one of the names, and depends on it in a subsequent patch
   (http://patchwork.ozlabs.org/patch/284512/).

 - Made max oobfree/eccpos configurable, and used this on tricorder,
   alpr, ASH405, T4160QDS, and T4240QDS (these boards failed to build
   for me without doing so, due to a size increase).

   On tricorder SPL, this saves 2576 bytes (and makes the SPL build
   again) versus the new default of 640 eccpos and 32 oobfree, and
   saves 336 bytes versus the old default of 128 eccpos and 8 oobfree.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Vipin Kumar <vipin.kumar@st.com>
[scottwood@freescale.com: changes as described above]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>