u-boot.git/include/configs, branch v2014.04-rc2

Merge branch 'master' of git://git.denx.de/u-boot-arm

2014-03-10T18:22:54+00:00

m68k: Remove M5271EVB and idmr board support

2014-03-10T15:38:13+00:00

CONFIG_SYS_HZ must be always 1000, but M5271EVB.h defines it
as 1000000 and idmr.h defines it as (50000000 / 64).

When compiling these two boards, a warning message is displayed:

  time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000
  and should not be defined by platforms" [-Wcpp]

There are no board maintainers for them so this commit just
deletes them.

Signed-off-by: Masahiro Yamada 
Cc: Jason Jin

arm: atmel: sama5d3: add nand spl boot support

2014-03-09T18:19:13+00:00

Add NAND SPL boot support with hardware PMECC.

Signed-off-by: Bo Shen 
Signed-off-by: Andreas Bießmann

arm: atmel: sama5d3: add spi spl boot support

2014-03-09T18:18:33+00:00

Add SPI SPL boot support for sama5d3xek board.

Signed-off-by: Bo Shen 
Signed-off-by: Andreas Bießmann

ARM: atmel: add sama5d3 Xplained board support

2014-03-09T18:09:50+00:00

Add sama5d3 Xplained board support which use Atmel SAMA5D36 SoC.
Now it supports boot from NAND flash and SD/MMC card.
Features support:
  - NAND flash
  - SD/MMC card
  - Two USB hosts
  - Ethernet (one GMAC, one EMAC)

Signed-off-by: Bo Shen 
[reorder boards.cfg]
Signed-off-by: Andreas Bießmann

at91sam9263ek: add mmc support

2014-03-09T17:24:52+00:00

Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.

Please note that this hooks up slot1 (MCI1) for SD. Not both.

Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).

CONFIG_ATMEL_MCI_PORTB not tested.

Signed-off-by: Andreas Henriksson 
[remove empty line]
Signed-off-by: Andreas Bießmann

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

2014-03-08T01:54:22+00:00

powerpc/t104xrdb: Update DDR initialization related settings

2014-03-07T22:53:48+00:00

Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
 but on T104xRDB, on setting this , DDR instability is observed.
 Board-level debugging is in progress.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.

Signed-off-by: Priyanka Jain 
Signed-off-by: York Sun

powerpc/t1040qds: Add Video - HDMI support

2014-03-07T22:53:40+00:00

T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder

Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board

Signed-off-by: Priyanka Jain 
Reviewed-by: York Sun

powerpc/t2080rdb: Add T2080PCIe-RDB board support

2014-03-07T22:53:13+00:00

T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
It works in two mode: standalone mode and PCIe endpoint mode.

T2080PCIe-RDB Feature Overview
------------------------------
Processor:
 - T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
 - Single memory controller capable of supporting DDR3 and DDR3-LP devices
 - 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
 - Two 10M/100M/1G RGMII ports on-board
 - Two 10Gbps SFP+ ports on-board
 - Two 10Gbps Base-T ports on-board
Accelerator:
 - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
 - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
 - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
 - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
 - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
 - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
 - SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus:
 - NOR:  128MB 16-bit NOR flash
 - NAND: 512MB 8-bit NAND flash
 - CPLD: for system controlling with programable header on-board
eSPI:
 - 64MB N25Q512 SPI flash
USB:
 - Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
 - One PCIe x4 gold-finger
 - One PCIe x4 connector
 - One PCIe x2 end-point device (C293 Crypto co-processor)
SATA:
 - Two SATA 2.0 ports on-board
SDHC:
 - support a TF-card on-board
I2C:
 - Four I2C controllers.
UART:
 - Dual 4-pins UART serial ports

Signed-off-by: Shengzhou Liu 
Reviewed-by: York Sun