u-boot-imx-2019-02-16 --------------------- - vhybrid: add calibration - gw_ventana: fixes - Improve documentation for Secure Boot (HABv4) - Fix Marvell Switch - MX6 Sabre, switch to DM - Fixes for NAND
This patch fixes a few values that were incorrect, and this now lets SPL boot from NAND. Signed-off-by: Adam Ford <aford173@gmail.com>
All options have been moved to Kconfig and there is no need to have board header files. Mini configurations require them that's why they are still there. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPD autodetection hasn't been enabled that's why there is zero size difference if that options are enabled/disabled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace SDHCI controller listing by Kconfig symbol to let SPL know that this board is using multiple SDHCIs controllers. Kconfig help message should explain why this is needed. Origin symbols were used in full u-boot but with moving to distro boot this was fixed already. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio subsystem already. That's why also remove CMD_PCA953X which is only for this driver. zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address. DM_I2C is not enabled for the whole SoC because it increase size for mini configurations and there is no I2C symbol present to setup dependencies. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
All these board have also eeprom enabled that's why it is also enabled via defconfig. There is also no need to have zc70x specific config file that's why also remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Boards have only one controller enabled that's why move to DM_I2C is easy. Add also i2c alias for not to be shown as i2c bus -1 because alias doesn't exist. Config file points to MAC stored in eeprom but it is not listed that's why I have added 24c08 part. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal. This configuration is very minimal in size which runs from OCM. It contains support for mtest which can be used for running DDR memory tests. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds distro boot commands for qspi, ospi and mmc. The distro boot commands now reads the script from flash offset of 63.5MB for qspi and ospi and executes it. For mmc its same as generic distro boot command. As either one of the qspi or ospi can exist on hardware, defined a single distroboot command as xspi that works for both. Setup default location via script_offset_f to 63.5MB to match the most xilinx reference boards for qspi, ospi for now. 512kB allocated space for script size (script_size_f) should be more than enough to cover custom boot logic. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>