u-boot.git/include/configs, branch v2022.04

board: gateworks: venice: determine dram size at runtime

2022-03-31T12:27:52+00:00

The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.

Signed-off-by: Tim Harvey 
Reviewed-by: Fabio Estevam

arm: socfpga: vining: Fix mtdparts for 2x256 MiB SF variant

2022-03-28T19:49:03+00:00

The 2x256 MiB SF variant of this system has 192 MiB rootfs MTD partition
containing UBI on SF0, use the correct size in U-Boot environment, else
U-Boot cannot mount UBI and boot on this variant.

Signed-off-by: Marek Vasut 
Cc: Siew Chin Lim 
Cc: Simon Goldschmidt 
Cc: Tien Fong Chee 
Cc: Tom Rini

rockchip: bob: Enable more configs

2022-03-18T10:12:03+00:00

This patch enables some configs that should be working on the Bob board,
based on what is observed to work on the Kevin board.

The Bob board uses an Embedded DisplayPort panel compatible with the
simple panel and Rockchip eDP drivers. Its backlight is controlled by
the Chromium OS Embedded Controller Pulse Width Modulator. Enable these
for the board.

Also set VIDEO_ROCKCHIP_MAX_{XRES,YRES} to 1280x800, the resolution of
its panel. This had to be done for the Kevin board, but it's untested if
this is actually necessary for Bob.

The Rockchip video driver needs to assert/deassert some resets, so also
enable the reset controller. RESET_ROCKCHIP defaults to y for this board
when DM_RESET=y, so it's enough to set that.

The Bob board has two USB 3.0 Type-C ports and one USB 2.0 Type-A port
on its right side. Enable the configs relevant to USB devices so these
can be used. This is despite a known issue with RK3399 boards where USB
de-init causes a hang, as there is a known workaround.

Some other rk3399-based devices enable support for the SoC's random
number generator in commit a475bef5340c ("configs: rk3399: enable rng on
firefly/rock960/rockpro64"), as it can provide a KASLR seed when booting
using UEFI. Enable it for Bob as well.

The default misc_init_r() for Rockchip boards sets cpuid and ethernet
MAC address based on e-fuse block. A previous patch extends this on Gru
boards to set registers related to SoC IO domains as is necessary on
these boards. Enable this function and configs for it on Bob.

The microSD card slot on this board (and others based on Gru) is
connected to a GPIO controlled regulator (ppvar-sd-card-io), which must
be operable by U-Boot. Enable the relevant config option to allow this.

Bob boards also use the Winbond W25Q64DW SPI flash chip, enable support
for Winbond SPI flash chips in the board config so U-Boot can boot with
this chip.

Signed-off-by: Alper Nebi Yasak 
Reviewed-by: Kever Yang 
Reviewed-by: Simon Glass 
Tested-by: Simon Glass

Merge https://source.denx.de/u-boot/custodians/u-boot-riscv

2022-03-16T12:11:53+00:00

- k210 updates

k210: use the board vendor name rather than the marketing name

2022-03-15T09:43:11+00:00

"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.

Signed-off-by: Damien Le Moal 
Signed-off-by: Niklas Cassel 
Reviewed-by: Leo Yu-Chi Liang

Nokia RX-51: Convert to CONFIG_DM_VIDEO

2022-03-09T20:28:53+00:00

Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.

As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.

This change was tested in qemu n900 machine and is working fine.

What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.

Signed-off-by: Pali Rohár

configs: ti: use standard configuration nodes naming

2022-03-04T20:20:06+00:00

Currently, any u-boot bootloader for ti armv7 platforms using
DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1)
doesn't boot when built with Yocto Poky (openembedded-core).

  ## Loading kernel from FIT Image at 90000000 ...
  Could not find configuration node
  ERROR: can't get kernel image!

Arago forked the kernel-fitimage class [1] and altered the
configuration nodes naming while adding the OPTEE support by
using FITIMAGE_CONF_BY_NAME by default [2].

The "upstream" kernel-fitimage class from openembedded-core still
add the "conf-" prefix for each configuration nodes [3].

The ITS file format (from doc/uImage.FIT/source_file_format.txt)
is not really accurate with the expected naming of these nodes.
But in practice the "conf-" prefix is widely used.

When the FIT image support has been added for ti armv7 platforms
the naming from Arago has been used [3]. Fix this issue by adding
the prefix expected by the ITS file generated by kernel-fitimage
class from openembedded-core.

[1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=719ab1b2098bcdc59c249e3529fa82cb1b9130e6
[2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=f23f2876a0cda89241d031bb7ba0b4256ed90035
[3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fitimage.bbclass?h=yocto-3.1.13#n290
[3] 1e93cc8473e4fe018aececc8ed3bf8fc2b3ff561

Signed-off-by: Romain Naour 
Cc: Tom Rini 
Reviewed-by: Denys Dmytriyenko

Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq

2022-03-03T13:24:13+00:00

Update and fixes for sl28, lx2, pblimage generation for some powerpc
products

arm: apple: Switch to fully dynamic mem layout

2022-02-28T15:33:45+00:00

Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().

Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).

Signed-off-by: Janne Grunau 
Reviewed-by: Mark Kettenis

lx2160a: Fix distroboot device list for configs without USB/SCSI/etc

2022-02-28T06:31:02+00:00

The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.

To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.

Signed-off-by: Daniel Klauer 
Reviewed-by: Priyanka Jain