u-boot.git/include/configs, branch v2022.07-rc4

Merge https://source.denx.de/u-boot/custodians/u-boot-riscv

2022-05-27T12:50:42Z

riscv: qemu: Set kernel_comp_addr_r for compressed kernel

2022-05-26T10:42:34Z

Set kernel_comp_addr_r and kernel_comp_size for compressed kernel. Adjust existing addresses for ramdisk, so that kernel_comp_addr_r comes before the ramdisk image, since the decompressed kernel size is known to us. This way we can allow big ramdisk image to be loaded. Signed-off-by: Bin Meng Reviewed-by: Leo Yu-Chi Liang

riscv: sifive: unleashed: Set kernel_comp_addr_r for compressed kernel

2022-05-26T10:42:34Z

Set kernel_comp_addr_r and kernel_comp_size for compressed kernel. Adjust existing addresses for ramdisk, so that kernel_comp_addr_r comes before the ramdisk image, since the decompressed kernel size is known to us. This way we can allow big ramdisk image to be loaded. Update unleashed.rst to remove the manual environment configuration for compressed kernel boot. Signed-off-by: Bin Meng Reviewed-by: Leo Yu-Chi Liang

riscv: sifive: unmatched: Adjust for big ramdisk image

2022-05-26T10:42:33Z

Move kernel_comp_addr_r to an address that comes before the ramdisk image, since the decompressed kernel size is known to us. This way we can allow big ramdisk image to be loaded. Signed-off-by: Bin Meng Reviewed-by: Leo Yu-Chi Liang

Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

2022-05-25T13:50:08Z

Xilinx changes for v2022.07-rc4 zynqmp: - Fix DP PLL configuration for zcu102/zcu106 and SOM - Fix split mode for starting R5s - DT fixes - Remove firmware node for mini configurations - Wire TEE for multi DTB fit image xilinx: - Handle board_get_usable_ram_top(0) properly phy: - Extend psgtr timeout mmc: - Fix mini configuration which misses zynqmp_pm_is_function_supported()

arm: socfpga: Add the terasic de10-standard board

2022-05-23T19:28:07Z

Use the de10-nano files as templates for the de10-standard board. The files in qts directory are generated by quartus from the GHRD design. Signed-off-by: Humberto Naves Reviewed-by: Marek Vasut

ARM: dts: imx: Add support for DH electronics i.MX8M Plus DHCOM and PDK2

2022-05-23T09:37:58Z

Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board. Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD, SPI NOR and USB 3.0 host. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Peng Fan Cc: Stefano Babic

ARM: imx6: Remove CONFIG_FEC_MXC_PHYADDR from DH header

2022-05-20T10:36:48Z

Use phy address from device tree instead of CONFIG_FEC_MXC_PHYADDR from board header. This is required, because the DH picoITX and DRC02 boards require different settings than PDK2. The corresponding 'phy-handle' device tree properties are already there. I tested this change on picoITX and DRC02, but on PDK2 it is untested. Reviewed-by: Marek Vasut Signed-off-by: Philip Oberfichtner

imx: imx8mp_rsb3720a1: convert to DM_SERIAL

2022-05-20T10:36:48Z

Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already marked with u-boot,dm-spl. Signed-off-by: Peng Fan Reviewed-by: Fabio Estevam

bosch: Add initial board support for ACC

2022-05-20T10:36:48Z

The Bosch ACC (Air Center Control) Board is based on the i.MX6D. The device tree is copied from Linux, see [1]. The only difference compared to the Linux DT is the removal of usbphynop properties. They are defined in the Linux version of imx6qdl.dtsi, but not in the u-boot version. [1] Commit 6192cf8ac082 from git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git Signed-off-by: Philip Oberfichtner