u-boot.git/include/configs, branch v2022.10-rc2

net: dwc_eth_qos: remove use of DWC_NET_PHYADDR

2022-08-08T14:50:20Z

Only two boards in the tree set the macro DWC_NET_PHYADDR. Both have CONFIG_DM_ETH_PHY=y, so should set the phy address in DT if necessary. The imx8mp_evk does set the correct address in device tree. The other board seems to be a copy-paste-adapt from an old version of the imx8mp_evk config header, given the "#ifdef CONFIG_DWC_ETH_QOS" block that has been removed from imx8mp_evk header in commit 127fb454955. Its device tree doesn't even enable (i.e., set 'status = "okay"') the &eqos node. But the other ethernet device, &fec, does get enabled, and does have a phy sitting at address 4 (and it also has a corresponding legacy #define CONFIG_FEC_MXC_PHYADDR 4). So I believe it should be completely safe to remove it from there as well. Signed-off-by: Rasmus Villemoes Reviewed-by: Ramon Fried [trini: Re-apply to top of tree, update imx93_evk.h] Signed-off-by: Tom Rini

Convert CONFIG_SYS_FSL_DDR_INTLV_256B to Kconfig

2022-08-04T20:18:48Z

This converts the following to Kconfig: CONFIG_SYS_FSL_DDR_INTLV_256B Signed-off-by: Tom Rini

Convert CONFIG_FSL_MEMAC et al to Kconfig

2022-08-04T20:18:48Z

This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini

Convert CONFIG_FSL_CORENET to Kconfig

2022-08-04T20:18:47Z

This converts the following to Kconfig: CONFIG_FSL_CORENET Signed-off-by: Tom Rini

configs: Remove a number of unreferenced CONFIG options.

2022-08-04T20:18:47Z

There are a large number of options under CONFIG_SYS (but some of these are elsewhere, spotted while cleaning CONFIG_SYS) that are never referenced, or only used slightly later in the config file. Remove or restructure these. Signed-off-by: Tom Rini

Convert CONFIG_SYS_FLASH_QUIET_TEST to Kconfig

2022-08-04T20:18:47Z

This converts the following to Kconfig: CONFIG_SYS_FLASH_QUIET_TEST Signed-off-by: Tom Rini

Convert CONFIG_SYS_MAX_FLASH_SECT to Kconfig

2022-08-04T20:18:47Z

This converts the following to Kconfig: CONFIG_SYS_MAX_FLASH_SECT Signed-off-by: Tom Rini

Convert CONFIG_FLASH_CFI_LEGACY to Kconfig

2022-08-04T20:18:47Z

This converts the following to Kconfig: CONFIG_FLASH_CFI_LEGACY Signed-off-by: Tom Rini

Convert CONFIG_SYS_FLASH_ERASE_TOUT et al to Kconfig

2022-08-04T20:18:47Z

This converts the following to Kconfig: CONFIG_SYS_FLASH_ERASE_TOUT CONFIG_SYS_FLASH_LOCK_TOUT CONFIG_SYS_FLASH_UNLOCK_TOUT CONFIG_SYS_FLASH_WRITE_TOUT In practice, for two m68k platforms we move to hard-coding with a comment the timeout values, rather than try and make convoluted Kconfig logic. We add options for the write and erase options to the pic32 flash driver, as this driver does make use of them. Everywhere else these are unreferenced values. Signed-off-by: Tom Rini

Convert CONFIG_SYS_FLASH_CHECKSUM to Kconfig

2022-08-04T20:18:47Z

This converts the following to Kconfig: CONFIG_SYS_FLASH_CHECKSUM Signed-off-by: Tom Rini