Later versions of Colibri iMX7D V1.1B modules use a "new" SoC fusing. The
difference lies in whether we enable the boot ROM to use the eMMC reset
signal. Depending on the SoC fuse, the boot ROM configures this pin as a
GPIO output to drive the reset signal. Our eMMC vs NAND detection
currently only sets that signal to a GPIO without explicitly setting any
direction. Previously, by default, it was set as an input. As the boot ROM
now configures it as an output, we receive a value of zero instead of one,
indicating the absence of the pull-up on eMMC modules.

To fix this, set the SION bit, allowing the reading back of the value
even if it is configured as an output by the boot ROM. It's important to
note that with the new SoC fusing, we now read back what the boot ROM
drives rather than the real value caused by the pull-up resistor. However,
if it were ever driven low, the eMMC would permanently be reset.

In addition, remove hard-coded variant in the eMMC build case as since the
commit 0c39564d0281 ("toradex: colibri_imx7: Enable nand/emmc detection
and set boot variant") will anyways always get overridden by the detection
routing in board code.

Fixes: 0c39564d ("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>

device tree overlay support requires fdtoverlay_addr_r to be set

before
~~~~~~
Invalid fdtoverlay_addr_r for loading overlays

after
~~~~~
Retrieving file: /boot/overlay/rtc-ds3231.dtbo

Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>

- Fix some issues Coverity has reported, update MAINTAINERS file,
  another bootstd fix, typo fix in error message, gitignore fix and
  update TI's URL in many places.

Replace instances of http://www.ti.com with https://www.ti.com

Signed-off-by: Nishanth Menon <nm@ti.com>

QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.

UART and boot over SD/eMMC/RJ45 are tested to work.

Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")

Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>

Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration.
Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files
to allow enabling them for armada boards.

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921112043.3144726-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

This adds support for the Inteno XG6846 board based on the
Broadcom MIPS 6328 SoC.

The default boot will read a uImage from flash and boot it.

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

USB_DFU was added in meson64.h but is missing in libretech-ac.h,
fix this to enable DFU RAM boot for libretech-ac.

Fixes 4aa027b3f8 ("configs: meson64: add alternate USB DFU boot target")

Link: https://lore.kernel.org/r/20231102-libretech-ac-fix-dfu-v1-1-112379165028@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>

Convert refresh USB to enter console. Transformers have full size
USB and a dock keyboard so access to U-Boot console would be handy.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>

U-boot initially loads the kernel image to the kernel_addr_r, and
subsequently relocates it to memory address 0x80200000. Setting
kernel_addr_r to 0x80200000 can eliminate one copy operation.

Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Tom Rini <trini@konsulko.com>