Without this patch, there will be error indicating that
"Cannot use 64 bit addresses with SDMA", and the booting
process will stuck.

please see full boot log below

U-Boot 2022.04-g18185931 (Sep 11 2024 - 13:15:30 +0800)

SoC:  LS1028AE Rev1.0 (0x870b0010)
Clock Configuration:
       CPU0(A72):1500 MHz  CPU1(A72):1500 MHz
       Bus:      400  MHz  DDR:      1600 MT/s
Reset Configuration Word (RCW):
       00000000: 3c004010 00000030 00000000 00000000
       00000010: 00000000 018f0000 0030c000 00000000
       00000020: 020031a0 00002580 00000000 00003296
       00000030: 00000000 00000010 00000000 00000000
       00000040: 00000000 00000000 00000000 00000000
       00000050: 00000000 00000000 00000000 00000000
       00000060: 00000000 00000000 200e705a 00000000
       00000070: bb580000 00000000
Model: LS1028A RDB Board
Board: LS1028AE Rev1.0-RDB, Version: C, boot from SD
FPGA: v8 (RDB)
SERDES1 Reference : Clock1 = 100.00MHz Clock2 = 100.00MHz
DRAM:  3.9 GiB
DDR    3.9 GiB (DDR4, 32-bit, CL=11, ECC on)
Using SERDES1 Protocol: 47960 (0xbb58)
PCIe1: pcie@3400000 Root Complex: no link
PCIe2: pcie@3500000 Root Complex: x1 gen2
Core:  45 devices, 22 uclasses, devicetree: separate
WDT:   Started watchdog@c000000 with servicing (60s timeout)
WDT:   Started watchdog@c010000 with servicing (60s timeout)
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

EEPROM: Invalid ID (ff ff ff ff)
In:    serial
Out:   serial
Err:   serial
SEC0:  RNG instantiated
Net:
Warning: enetc-0 (eth0) using random MAC address - d2:9b:a5:37:7b:b5
eth0: enetc-0
Warning: enetc-2 (eth1) using random MAC address - ca:57:11:de:de:cb
, eth1: enetc-2, eth2: swp0, eth3: swp1, eth4: swp2, eth5: swp3
Hit any key to stop autoboot:  0
Trying load HDP firmware from SD..
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes

MMC read: dev # 0, block # 18944, count 512 ... 512 blocks read: OK
Loading hdp firmware from 0x00000000a0000000 offset 0x0000000000002000
Loading hdp firmware Complete
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk mmc@2140000.blk...
Scanning disk mmc@2150000.blk...
Found 7 disks
ERROR: invalid device tree
Found EFI removable media binary efi/boot/bootaa64.efi
981992 bytes read in 44 ms (21.3 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
WARNING could not find node vivante,gc: FDT_ERR_NOTFOUND.
Booting /efi\boot\bootaa64.efi
Cannot use 64 bit addresses with SDMA
Error reading cluster
** Unable to read file /efi/boot/grubaa64.efi **
Unexpected return from initial read: Device Error, buffersize 29D790
Failed to load image ぀￢ : Device Error
start_image() returned Device Error
EFI LOAD FAILED: continuing...
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
Scanning mmc 1:2...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
starting USB...
Bus usb@3100000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb@3110000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus usb@3100000 for devices... 1 USB Device(s) found
scanning bus usb@3110000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
Trying load from SD ...
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes

MMC read: dev # 0, block # 32768, count 81920 ... 81920 blocks read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!

Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

The current A/B switching preparatory altbootcmd is confusing
to users, replace it with plain 'run bootcmd' which can be
replaced by proper A/B switching altbootcmd when the matching
updater is added on top of the platform. By default, keep the
boot counter incrementing, but do not do any A/B partition
switching.

Signed-off-by: Marek Vasut <marex@denx.de>

The x250 and SE250 are series of 10G L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>

As things have been moved to Kconfig there are a number of dead comments
left over in x530.h. Remove them.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Use standard boot instead of the distro boot scripts. Regenerate the
board defconfig now that some options are selected automatically.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Remove CFG_SYS_BAUDRATE_TABLE as there's no reason not to use the
defaults defined via config_fallbacks.h.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>

Enable bootstd for Sheevaplug board.
Remove JFFS2 support. See JFFS2 Vulnerability[1].
Enable LTO to keep board size within limit.
Move default envs to text-base environment

[1] https://lore.kernel.org/u-boot/20241114233005.GN3600562@bill-the-cat/T/#m2fc25da1d2c019bc3cd8676991fdd64b8a21aa9b

Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>

CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/23474

- UFS support is enabled for SC7280 and SM8150 platforms.
- Qualcomm dt-bindings headers are all dropped in favour of
  dts/upstream.
- The SMMU driver now correctly handles stream ID 0 and is disabled in
  EL2.
- Initial support for capsule updates (using the new dynamic UUIDs) is
  added for the RB3 Gen 2 board alongside a new SCSI backend for DFU.
- CONFIG_PINCONF is enabled in qcom_defconfig.
- The vqmmc supply is now enabled for sdcard support on boards that need
  it.
- A quirk is added for reading GPIOs on the PM8550 PMIC

Qualcomm boards flash U-Boot a variety of partitions, implement support
for determining which slot U-Boot is running from, finding the correct
partition for that slot and configuring the appropriate DFU string.

Initially, we only support the RB3 Gen 2 where U-Boot is flashed to the
UEFI partition, and ignore handling of slots. In the future we will
additionally support booting U-Boot from other partitions (e.g. boot)
and correct handling for A/B.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>

AMD/Xilinx changes for v2025.01-rc3:

- microblaze:
  - Disable JFFS2
- fpga:
  - pass compatible flag to fpga_load()
- zynqmp:
  - SOM RTC fix
  - SC(system controller) PMW polarity fix
  - Fix ram_top calculation with introducing XILINX_MINI
  - Fix RPU release command
- versal:
  - Enable capsule update
  - Enable soft reset and Micron octal flashes
- xilinx:
  - Align Kconfig regarding SPI_STACKED_PARALLEL
- bootcount:
  - Add new zynqmp driver