u-boot.git/include/dm, branch v2016.05-rc2

fdt: implement dev_get_addr_name()

2016-04-15T14:14:37+00:00

This function parses the reg property based on an index found in the
reg-names property. This is required for bindings that are written
using reg-names rather than hard-coding indices in reg.

Signed-off-by: Stephen Warren 
Acked-by: Simon Glass

drivers: Add SPMI bus uclass

2016-04-01T21:18:12+00:00

Qualcom processors use proprietary bus to talk with PMIC devices -
SPMI (System Power Management Interface).
On wiring level it is similar to I2C, but on protocol level, it's
multi-master and has simple autodetection capabilities.
This commit adds simple uclass that provides bus read/write interface.

Signed-off-by: Mateusz Kulikowski 
Reviewed-by: Simon Glass 
Tested-by: Simon Glass

serial: add BCM283x mini UART driver

2016-03-27T13:12:52+00:00

The RPi3 typically uses the regular UART for high-speed communication with
the Bluetooth device, leaving us the mini UART to use for the serial
console. Add support for this UART so we can use it.

Signed-off-by: Stephen Warren

serial: pl01x: Add support for devices with the rate pre-configured.

2016-03-22T16:16:12+00:00

For Raspberry Pi, we had the input clock rate to the pl011 fixed in
the rpi.c file, but it may be changed by firmware due to user changes
to config.txt.  Since the firmware always sets up the uart (default
115200 output unless the user changes it), we can just skip our own
uart init to simplify the boot process and more reliably get serial
output.

Signed-off-by: Eric Anholt 
Reviewed-by: Tom Rini 
Tested-by: Stephen Warren

dm: blk: Add a block-device uclass

2016-03-14T21:34:50+00:00

Add a uclass for block devices. These provide block-oriented data access,
supporting reading, writing and erasing of whole blocks.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng 
Tested-by: Stephen Warren

dm: core: Add uclass_first_device_err() to return a valid device

2016-03-14T21:34:50+00:00

A common pattern is to call uclass_first_device() and then check if it
actually returns a device. Add a new function which does this, returning
an error if there are no devices in that uclass.

Signed-off-by: Simon Glass

stm32x7: add support for stm32x7 serial driver

2016-02-24T23:43:54+00:00

This patch adds support for stm32f7 family usart peripheral.

Signed-off-by: Vikas Manocha 
Reviewed-by: Simon Glass

dm: implement a DMA uclass

2016-02-23T10:44:45+00:00

Implement a DMA uclass so that the devices like ethernet, spi,
mmc etc can offload the data transfers from/to the device and
memory.

Signed-off-by: Mugunthan V N 
Reviewed-by: Simon Glass 
Reviewed-by: Jagan Teki

video: sandbox: Allow selection of font size and console name

2016-01-30T09:57:30+00:00

For testing it is useful to be able to select the font size and the console
driver for sandbox. Add this information to platform data and copy it to
the video device when needed.

Signed-off-by: Simon Glass

dm: Remove device_probe_child()

2016-01-29T04:01:23+00:00

This function is not used as the use case for it did not eventuate. Remove
it to avoid confusion.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini 
Reviewed-by: Bin Meng