As part of moving to using OF_UPSTREAM and so the upstream dt-bindings
headers we have a number of these headers that are in our include
directory and differ only in combinations of spacing changes and/or
switching to SPDX license tags. We can safely remove the copies under
include/dt-bindings now to prevent future conflicts.

Signed-off-by: Tom Rini <trini@konsulko.com>

As part of moving to using OF_UPSTREAM and so the upstream dt-bindings
headers we have a number of these headers that are in our include
directory and are currently identical to the versions in dts/upstream.
We can remove these now to prevent future conflicts.

Signed-off-by: Tom Rini <trini@konsulko.com>

As part of moving to using OF_UPSTREAM and so the upstream dt-bindings
headers we have a number of these headers that are in our include
directory and not referenced by any code outside of dts/upstream. We can
remove these now to prevent future conflicts.

Signed-off-by: Tom Rini <trini@konsulko.com>

Based on Linux upstream discussion value enumeration shouldn't be used.
Instead of it delay in pS should be used that's why remove it from the
header.

Link: https://lore.kernel.org/all/YNsm%2F0dmpBgO8mqr@lunn.ch/
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/bbd343474856a67252f3b31d22b3b5a80ad04043.1698851109.git.michal.simek@amd.com

This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.

Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

This resyncs the dts files for all of the currently in-tree K3
platforms, along with relevant bindings, with the v5.14 Linux Kernel
release.  Of note are that the main-navss/mcu-navss nodes were renamed
to main_navss / mcu_navss and so the u-boot.dtsi files needed to be
updated to match.

Tested on j721e_evm and am65x_evm.

Signed-off-by: Tom Rini <trini@konsulko.com>

Add MSCC header with delay definitions for VSC8531 and associated
family devices.

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.

By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.

Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Based on commit 980066e6d964 ("dt-bindings: phy: dp83867: Add documentation
for disabling clock output") of mainline linux kernel.

The clock output is generally only used for testing and development and not
used to daisy-chain PHYs.  It's just a source of RF noise afterward.

Add a mux value for "off".  I've added it as another enumeration to the
output property.  In the actual PHY, the mux and the output enable are
independently controllable.  However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.

Document that PHY's default setting will be left as is if the property
is omitted.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Updating the bcm283x device tree sources adds the device trees for

- Raspberry Pi 3 Model A+
- Raspberry Pi 3 Model B+
- Raspberry Pi Compute Module IO board rev1
- Raspberry Pi Compute Module 3 IO board V3.0
- Raspberry Pi Zero

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>