The only call site of dwc3_uboot_handle_interrupt() is the dm_usb_gadget_handle_interrupts(), fold the former into the later. This makes dwc3_uboot_handle_interrupt() unavailable to be called from board code as well. Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3 Link: https://lore.kernel.org/r/20240317044357.547037-2-marek.vasut+renesas@mailbox.org Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The dm_usb_gadget_handle_interrupts() has no place in board code. Move this into DWC3 driver. The OMAP implementation is special, add new weak dwc3_uboot_interrupt_status() function to decide whether DWC3 interrupt handling should be called, and override it in OMAP DWC3 code, to repair the special OMAP interrupt handling code until OMAP gets switched over to DM UDC proper. Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # vim3 Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # qcom sdm845 Link: https://lore.kernel.org/r/20240317044357.547037-1-marek.vasut+renesas@mailbox.org Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Replace instances of http://www.ti.com with https://www.ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
The usb_gadget_handle_interrupts() is no longer used anywhere, replace the remaining uses with dm_usb_gadget_handle_interrupts() which takes udevice as a parameter. Some of the UDC drivers currently ignore the index parameter altogether, those also ignore the udevice and have to be reworked. Other like the dwc3_uboot_handle_interrupt() had to be switched from index to udevice look up to avoid breakage. Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3 Signed-off-by: Marek Vasut <marex@denx.de>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Reference from below Linux commit,
commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate
check quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk")
in Linux Rockchip Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")
in Linux Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Reference from below Linux commit,
commit <00fe081dc3a3> ("usb: dwc3: add dis_del_phy_power_chg_quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Get a group of phys by the phy bulk API Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
U-Boot has two different variants of dwc3 initializations, - with dm variant gadget, so the respective dm driver would call the dwc3_init in core. - with non-dm variant gadget, so the usage board file would call dwc3_uboot_init in core. The driver probe would handle all respective gadget properties including phy interface via phy_type property and then trigger dwc3_init for dm-variant gadgets. So, to support the phy interface for non-dm variant gadgets, the better option is dwc3_uboot_init since there is no dedicated controller for non-dm variant gadgets. This patch support for adding phy interface like 8/16-bit UTMI+ code for dwc3_uboot. This change used Linux phy.h enum list, to make proper code compatibility. Cc: Marek Vasut <marex@denx.de> Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>