The low four bits of the SYSCTL register are reserved on the USDHC
controller on i.MX6 and i.MX7 processors, but are used for clocking
operations on earlier models.

Guard against their usage by hiding the bit mask macros on those
processors.

These bits are used to prevent glitches when changing clocks on
i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7.

>From the i.MX6DQ RM:
	To prevent possible glitch on the card clock, clear the
	FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS
	or DVS in System Control Register) or setting RSTA bit.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Hector Palacios <hector.palacios@digi.com>

This patch adds esdhc support for ls1043ardb.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>

This patch adds esdhc support for ls2085a.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>

Add support of the DDR mode for eSDHC driver.
Enable it for i.MX6 SoC family only.

Signed-off-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Reviewed-by: York Sun <yorksun@freescale.com>

This adds support to switch to 1.8V in case CMD11 succeeds.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Marek Vasut <marex@denx.de>

For LS102xA, the processor is in little-endian mode, while esdhc IP is
in big-endian mode. CONFIG_SYS_FSL_ESDHC_LE and CONFIG_SYS_FSL_ESDHC_BE
are added. So accessing ESDHC registers can be determined by ESDHC IP's
endian mode.

Signed-off-by: Alison Wang <alison.wang@freescale.com>

Add support of loading image, binary for MMC and SPI during SPL boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>