u-boot.git/include/image.h, branch v2018.03-rc1

fix incorrect usage of DT node unit address in comments

2018-01-16T01:29:21Z

The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Fix all occurences in the tree where node names were mentioned in comments, to not give bad examples to the reader. Signed-off-by: Andre Przywara

riscv: Modify generic codes to support RISC-V

2018-01-12T13:05:12Z

Support common commands bdinfo and image format, also modify common generic flow for RISC-V. Signed-off-by: Rick Chen Signed-off-by: Rick Chen Signed-off-by: Greentime Hu Reviewed-by: Tom Rini

SPL: Add FIT data-position property support

2017-12-13T02:33:38Z

For external data, FIT has a optional property "data-position" which can set the external data to a fixed offset to FIT beginning. Add the support for this property in SPL FIT. Signed-off-by: Ye Li Signed-off-by: Peng Fan Reviewed-by: Simon Glass Reviewed-by: Tomas Melin Cc: Pantelis Antoniou Cc: "Andrew F. Davis" Cc: Igor Grinberg Cc: "tomas.melin@vaisala.com" Cc: Kever Yang Cc: Andre Przywara Cc: York Sun Cc: Lokesh Vutla Cc: "Cooper Jr., Franklin" Cc: George McCollister Cc: Tuomas Tynkkynen Cc: Jean-Jacques Hiblot Cc: Rick Altherr Cc: Tom Rini Reviewed-by: Lokesh Vutla Reviewed-by: York Sun

image: add IH_OS_ARM_TRUSTED_FIRMWARE for ARM Trusted Firmware

2017-11-25T23:39:06Z

To boot on ARMv8 systems with ARM Trusted Firmware, we need to assemble an ATF-specific parameter structure and also provide the address of the images started by ATF (e.g. BL3-3, which may be the full U-Boot). To allow us to identify an ARM Trusted Firmware contained in a FIT image, this adds the necessary definitions. Signed-off-by: Philipp Tomsich Reviewed-by: Simon Glass

common: Remove genimg_get_image()

2017-10-16T13:42:51Z

Removal of the legacy DataFlash code turned genimg_get_image() into a no-op. Drop all calls to it and the function itself. Signed-off-by: Tuomas Tynkkynen

fit: If no matching config is found in fit_find_config_node(), use the default one

2017-10-06T01:31:04Z

If board_fit_config_name_match() doesn't match any configuration node, then use the default one (if provided). Signed-off-by: Jean-Jacques Hiblot Reviewed-by: Tom Rini Reviewed-by: Simon Glass

fit: Introduce methods for applying overlays on fit-load

2017-09-15T11:27:49Z

Introduce an overlay based method for constructing a base DT blob to pass to the kernel. It is based on a specific method now to get the FDT from a FIT image named boot_get_fdt_fit(). Signed-off-by: Pantelis Antoniou Acked-by: Simon Glass

image: Add TI PMMC image type

2017-09-12T21:58:02Z

Add a new image type representing TI Power Management Micro-Controller (PMMC) Firmware image type. Signed-off-by: Andrew F. Davis

env: Rename some other getenv()-related functions

2017-08-16T12:31:11Z

We are now using an env_ prefix for environment functions. Rename these other functions as well, for consistency: getenv_vlan() getenv_bootm_size() getenv_bootm_low() getenv_bootm_mapsize() env_get_default() Suggested-by: Wolfgang Denk Signed-off-by: Simon Glass

env: Rename getenv/_f() to env_get()

2017-08-16T12:30:24Z

We are now using an env_ prefix for environment functions. Rename these two functions for consistency. Also add function comments in common.h. Quite a few places use getenv() in a condition context, provoking a warning from checkpatch. These are fixed up in this patch also. Suggested-by: Wolfgang Denk Signed-off-by: Simon Glass