Increase max sizes for OOB, Page size and eccpos to
suit for Micron MT29F32G08 part

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>

Update the NAND code to match Linux v4.1.  The previous sync was
from Linux v3.15 in commit 4e67c57125290b25.

CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout.  Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.

Signed-off-by: Scott Wood <scottwood@freescale.com>

In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().

While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67]
Signed-off-by: Scott Wood <scottwood@freescale.com>

I didn't approve the patch that added them.  Get them out of the way
before doing a sync.

Signed-off-by: Scott Wood <scottwood@freescale.com>

The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>

U-Boot has imported various source files from other projects,
mostly Linux.

Something like

  #ifdef __UBOOT__
    [ modification for U-Boot ]
  #else
    [ original code ]
  #endif

is an often used strategy for clarification of adjusted parts,
that is, easier re-sync in future.

Instead of defining __UBOOT__ in each source file,
passing it from the top Makefile would be easier.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>

snyc with linux v3.15:

commit 1860e379875dfe7271c649058aeddffe5afd9d0d
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Sun Jun 8 11:19:54 2014 -0700

    Linux 3.15

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>

resync ubi subsystem with linux:

commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Sun Mar 30 20:40:15 2014 -0700

    Linux 3.14

A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>

As per following Sections in ONFI Spec, GET_FEATURES and SET_FEATURES also need
byte-addressing on 16-bit devices.

*Section: Target Initialization"
"The Read ID and Read Parameter Page commands only use the lower 8-bits of the
 data bus. The host shall not issue commands that use a word data width on x16
 devices until the host determines the device supports a 16-bit data bus width
 in the parameter page."

*Section: Bus Width Requirements*
"When the host supports a 16-bit bus width, only data is transferred at the
 16-bit width. All address and command line transfers shall use only the lower
 8-bits of the data bus. During command transfers, the host may place any value
 on the upper 8-bits of the data bus. During address transfers, the host shall
 set the upper 8-bits of the data bus to 00h."

So porting following commit from linux kernel
    commit e34fcb07a6d57411de6e15a47724fbe92c5caa42
    Author: David Mosberger <davidm@egauge.net>  (preserving authorship)
    mtd: nand: fix GET/SET_FEATURES address on 16-bit devices

Signed-off-by: Pekon Gupta <pekon@ti.com>

As per following Sections in ONFI Spec, NAND_CMD_READID should use only
lower 8-bit for transfering command, address and data even on x16 NAND device.

*Section: Target Initialization"
"The Read ID and Read Parameter Page commands only use the lower 8-bits of the
 data bus. The host shall not issue commands that use a word data width on x16
 devices until the host determines the device supports a 16-bit data bus width
 in the parameter page."

*Section: Bus Width Requirements*
"When the host supports a 16-bit bus width, only data is transferred at the
 16-bit width. All address and command line transfers shall use only the lower
 8-bits of the data bus. During command transfers, the host may place any value
 on the upper 8-bits of the data bus. During address transfers, the host shall
 set the upper 8-bits of the data bus to 00h."

Thus porting  following commit from linux-kernel to ensure that column address
is not altered to align to x16 bus when issuing NAND_CMD_READID command.

    commit 3dad2344e92c6e1aeae42df1c4824f307c51bcc7
    mtd: nand: force NAND_CMD_READID onto 8-bit bus
    Author: Brian Norris <computersforpeace@gmail.com> (preserving authorship)

    The NAND command helpers tend to automatically shift the column address
    for x16 bus devices, since most commands expect a word address, not a
    byte address. The Read ID command, however, expects an 8-bit address
    (i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
    0x20).

    This fixes the column address for a few drivers which imitate the
    nand_base defaults.

Signed-off-by: Pekon Gupta <pekon@ti.com>