Drop all duplicate newlines. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>

Remove <common.h> from this board vendor directory and when needed
add missing include files directly.

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert UTF-8 chars to ASCII in cases where make sense. No Copyright or
names are converted.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Behún <kabel@kernel.org>

Add support for XTX XT26G0xA and XT26xxxD. The driver is ported from
linux-6.7.1. This driver is tested on Banana BPI-R3 with XT26G01A and
XT26G12D.

Link: https://lore.kernel.org/all/20240312014314.15454-1-bruce_suen@163.com
Signed-off-by: Bruce Suen <bruce_suen@163.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>

Introduced in upstream Linux with commit 7a08dbaedd365 for release v5.0.

When the new atmel nand driver was backported to U-Boot with commit
6a8dfd57220d ("nand: atmel: Add DM based NAND driver") that definition
was added to the driver instead of the header file.  Move it over to the
other definitions with the same help text it has in Linux.

Code actually using this has not been ported over to raw nand base yet.

Link: https://lore.kernel.org/all/20240320090214.40465-3-ada@thorsis.com
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>

Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Infineon(Cypress) S28Hx-T family does not support legacy CLSR(0x30) opcode.
Instead, it supports CLPEF(0x82) which has the same functionality as CLSR.
spansion_sr_ready() is for multi-die package parts including S28HS02GT, so
we need to use CLPEF instead of CLSR.

This change does not affect to S25x02GT which uses spansion_sr_ready() as
S25Hx-T family also supports CLPEF(0x82) as well as CLSR(0x30).

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().

Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>