Introduce response and request structs to receive and request
information regarding DM version, etc from TI SCI.

Signed-off-by: Moteen Shah <m-shah@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>

Introduce response and request structs for receiving information
regarding FW/SOC capability from DM. The received capability can
further be used to call certain API's based on the feature supoorted
by the DM firmware.

Signed-off-by: Moteen Shah <m-shah@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>

When FIT image with multiple dtbs are involved for R5 boot process,
R5 SPL starts off with the first instance of dtb to probe the
eeprom, then once we have identified the type of board, invocation
of setup_multi_dtb_fit will replace the gd->fdt_blob with the proper
board dtb match. However, when we do this, two things happen:

a) Prior to the invocation of setup_multi_dtb_fit, as part of the eeprom
   discovery process, i2c controller device is already probed and marked
   as exclusive with the match of the very first tisci match (from the
   original boot dtb). This list is stored in the info->dev_list of the
   first probe.
b) When the second dtb is loaded, tisci is probed again (since this is a
   new node) and the new info->dev_list is empty.

At this stage, the exclusive devices such as i2c instances used to
probe the board information is left in the old info->dev_list that is
no longer used actively by the system using the replaced dtb.

As a result of this, the cleanup we intend to do with
ti_sci_cmd_release_exclusive_devices is no longer complete and
leaves the instances such as i2c for eeprom marked used as we scan just
the new info->dev_list.

This creates a problem when Device Manager(DM) firmware starts up later
on in the boot process and identifies that this instance of i2c is
already marked active, so it assumes this can no longer be controlled
by software and is marked internally as reserved and HLOS can no
longer control these instances. This defeated the purpose of
ti_sci_cmd_release_exclusive_devices.

NOTE: This scheme works just fine if the FIT has just a single dtb as
the info->dev_list is upto date.

To fix this, let us make ti_sci_cmd_release_exclusive_devices scan the
all registrations of tisci instances and cleanup all exclusive devices
that have ever been registered.

As part of this, change the prototype of release_exclusive_devices to
drop the handle since that has no further meaning now.

Though this issue was identified on AM64-sk, this can be present in
other builds which use multi-fit-dtb for R5 SPL startup.

Fixes: 9566b777ae0a ("firmware: ti_sci: Add a command for releasing all exclusive devices")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>

Replace instances of http://www.ti.com with https://www.ti.com

Signed-off-by: Nishanth Menon <nm@ti.com>

This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h

Move this out of the common header and include it only where needed.

Signed-off-by: Simon Glass <sjg@chromium.org>

The common TI SCI header file uses some macros from err.h and these
get exercised when CONFIG_TI_SCI_PROTOCOL is not defined. Include
the linux/err.h header file in this header file directly rather
than relying on source files to include it to eliminate any
potential build errors.

While at this, reorder the existing header file include to the
beginning of the file.

Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>

With AM64x supporting only K3_NAV_RINGACC_RING_MODE_RING or the exposed
ring mode, all other K3 SoCs have also been moved to this common
baseline. Therefore drop other modes such as
K3_NAV_RINGACC_RING_MODE_MESSAGE (and proxy) to save on SPL footprint.

There is a saving of ~800 bytes with this change for am65x_evm_r5_defconfig.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>

AM64 dual mode rings are modeled as pair of Rings objects which has common
configuration and memory buffer, but separate real-time control register
sets for each direction mem2dev (forward) and dev2mem (reverse).

AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Update struct ti_sci_msg_rm_udmap_tx_ch_cfg_req to latest ABI to support
AM64x BCDMA Block copy channels.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>

Add new API k3_ringacc_request_rings_pair() to request pair of rings at
once, as in the most case Rings are used with DMA channels which required
to request pair of rings - one to feed DMA with descriptors (TX/RX FDQ) and
one to receive completions (RX/TX CQ). This will allow to simplify Ringacc
API users.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>