u-boot.git/include/miiphy.h, branch v2012.04

net/miiphy/serial: drop duplicate "NAMESIZE" define

2012-03-18T19:11:22+00:00

A few subsystems are using the same define "NAMESIZE".  This has been
working so far because they define it to the same number.  However, I
want to change the size of eth_device's NAMESIZE, so rather than tweak
the define names, simply drop references to it.  Almost no one does,
and the handful that do can easily be changed to a sizeof().

Signed-off-by: Mike Frysinger

Revert "mii: miiphy register address width change"

2011-12-07T07:35:14+00:00

This reverts commit 5c45a22b9203351a32aec4600514341b91175542.

It causes a lot of "incompatible pointer type" warnings for a large
number of Ethernet drivers, which are not really worth fixing
especially as this patch was only supposed to help the old,
deprecated miiphy API.  Instead of adding more efforts to a lost case
we rather revert it.

Signed-off-by: Wolfgang Denk

mii: miiphy register address width change

2011-12-06T20:01:01+00:00

This patch is added for PHY whose register offset value exceeds 0xFF and
cannot be used with "unsigned char" datatype in miiphy_read, miiphy_write
and miiphy_register functions. Datatype of register offset is changed to
unsigned short instead of unsigned char so that offset value greater then
0xFF can be used.

Signed-off-by: Chandan Nath 
Acked-by: Mike Frysinger

Create PHY Lib for U-Boot

2011-04-20T20:09:19+00:00

Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming 
Signed-off-by: Kumar Gala 
Acked-by: Detlev Zundel

miiphy: Fix some formatting issues

2011-04-20T18:44:46+00:00

Mostly putting a space between function name and "(", and
doing return (foo)

Signed-off-by: Andy Fleming 
Acked-by: Detlev Zundel

miiphy: convert to linux/mii.h

2011-01-09T17:06:50+00:00

The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.

Signed-off-by: Mike Frysinger

miiphy: constify device name

2010-08-09T18:52:29+00:00

The driver name does not need to be writable, so constify it.

Signed-off-by: Mike Frysinger 
Signed-off-by: Ben Warren

Rewrite the miiphybb (Bit-banged MII bus driver) in order to support an arbitrary number of mii buses.

2009-10-11T06:16:53+00:00

This feature is useful when your board uses different mii buses for different
phys and all (or a part) of these buses are implemented via bit-banging mode.

The driver requires that the following macros should be defined into the board
configuration file:

CONFIG_BITBANGMII       - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support

If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:

MII_INIT      - Generic code to enable the MII bus (optional)
MDIO_DECLARE  - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE   - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ     - Read the MDIO pin
MDIO(v)       - Write v on the MDIO pin
MDC_DECLARE   - Declaration needed to access to the MDC pin (optional)
MDC(v)        - Write v on the MDC pin

The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).

When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):

char name[]            - The symbolic name that must be equal to the MII bus
                         registered name
int (*init)()          - Initialization function called at startup time (just
                         before the Ethernet initialization)
int (*mdio_active)()   - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)()      - Write the MDIO pin
int (*get_mdio)()      - Read the MDIO pin
int (*set_mdc)()       - Write the MDC pin
int (*delay)()         - Delay function
void *priv             - Private data used by board specific code

The board code will look like:

struct bb_miiphy_bus bb_miiphy_buses[] = {
 { .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... },
 { .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... },
 ...
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
                          sizeof(bb_miiphy_buses[0]);

Signed-off-by: Luigi 'Comio' Mantellini 
Signed-off-by: Ben Warren

Dual-license IBM code contributions

2009-08-09T21:15:33+00:00

It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards.  As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.

IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.

Signed-off-by: Josh Boyer

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03+00:00

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD