u-boot.git/include/phy_interface.h, branch v2022.04

net: replace the "xfi" phy-mode with "10gbase-r"

2021-09-28T15:50:56+00:00

As part of the effort of making U-Boot work with the same device tree as
Linux, there is an issue with the "xfi" phy-mode. To be precise, in
Linux there was a discussion (for those who have time to read:
https://lore.kernel.org/netdev/1576768881-24971-2-git-send-email-madalin.bucur@oss.nxp.com/)

which led to a patch:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c114574ebfdf42f826776f717c8056a00fa94881

TL;DR: "xfi" was standardized in Linux as "10gbase-r".

This patch changes the relevant occurrences in U-Boot to use "10gbase-r"
instead of "xfi" wherever applicable.

Signed-off-by: Vladimir Oltean 
Reviewed-by: Ramon Fried

phy: introduce 1000BaseX and 2500BaseX modes

2021-05-20T11:03:30+00:00

Signed-off-by: Stefan Chulski 
Signed-off-by: Stefan Roese

net: Drop dm.h header file from phy.h

2020-08-04T02:19:54+00:00

This header file should not be included in other header files. Remove it
and use other headers and C inclusions instead.

Signed-off-by: Simon Glass

phy: add support for backplane kr mode

2020-04-20T08:05:11+00:00

Add generic support for backplane kr modes currently available:
10gbase-kr, 40gbase-kr4. Remove platform generic fixups
(armv8/layerscape and powerpc) for ethernet interfaces specified
in device tree as supported backplane modes.

Signed-off-by: Florinel Iordache 
Reviewed-by: Priyanka Jain

phy: Include NC-SI in phy setup

2020-03-09T23:11:23+00:00

Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.

Signed-off-by: Samuel Mendoza-Jonas 
Reviewed-by: Joel Stanley 
Acked-by: Joe Hershberger

include: phy: define XFI and USXGMII interface types

2019-12-09T15:47:42+00:00

Drivers currently use XGMII for XFI and USXGMII and, where needed, use
other information to identify the actual protocol on the board.  With these
two defined drivers can now rely on DT phy-mode property.

Signed-off-by: Alex Marginean 
Acked-by: Joe Hershberger

phy: Add 25G_AUI, XLAUI, CAUI2, CAUI4 related macros

2018-10-10T17:28:55+00:00

NXP SoCs like LX2160A can support new ethernet modes
which are 25G_AUI(25G), XLAUI(40G), CAUI2(50G)
and CAUI4(100G)
Add corresponding macros definitions in phy_interface.h

Signed-off-by: Priyanka Jain 
Acked-by: Joe Hershberger

phy: Break include cycle

2018-07-26T19:08:22+00:00

Because some phy wants to export some functions [1], export.h was
including the whole phy subsystem which pulls in lots of stuff that
causes some ordering and redefinition issues. Split out the only part
that is actually needed in export.h and include it there and in phy.h.

[1] commit 95279315076c ("board/ls2085rdb: Export functions for
			  standalone AQ FW load apps")

Signed-off-by: Joe Hershberger