u-boot.git/include/power/regulator.h, branch v2023.07.01

doc: replace @return by Return:

2022-01-19T17:11:34Z

Sphinx expects Return: and not @return to indicate a return value. find . -name '*.c' -exec \ sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \; find . -name '*.h' -exec \ sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \; Signed-off-by: Heinrich Schuchardt

power: regulator: Add support for regulator-force-boot-off

2021-04-29T05:38:57Z

Add support for regulator-force-boot-off DT property. This property can be used by the board/device drivers for turning off regulators on early init stages as pre-requisite for the other components initialization. Signed-off-by: Konstantin Porotchkin Signed-off-by: Stefan Roese Cc: Jaehoon Chung Cc: Simon Glass Reviewed-by: Jaehoon Chung

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42Z

Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include at all, so remove that include. Signed-off-by: Simon Glass Signed-off-by: Tom Rini

dm: treewide: Rename 'platdata' variables to just 'plat'

2020-12-13T23:51:08Z

We use 'priv' for private data but often use 'platdata' for platform data. We can't really use 'pdata' since that is ambiguous (it could mean private or platform data). Rename some of the latter variables to end with 'plat' for consistency. Signed-off-by: Simon Glass

dm: Remove uses of device_bind_offset()

2020-12-13T14:58:18Z

This function is not needed since the standard device_bind() can be used instead. Signed-off-by: Simon Glass

dm: core: Rename device_bind() to device_bind_offset()

2020-12-13T14:58:17Z

This function is not necessary anymore, since device_bind_ofnode() does the same thing and works with both flattree and livetree. Rename it to indicate that it is special. Signed-off-by: Simon Glass

power: regulator: add dummy helper

2020-10-23T20:38:33Z

Add dummy helper to enabling the header could be included when DM REGULATOR not enabled. Signed-off-by: Peng Fan

dm: regulator: support regulator more state

2019-11-10T12:31:09Z

support parse regulator standard property: regulator-off-in-suspend; regulator-init-microvolt; regulator-suspend-microvolt: regulator_get_suspend_enable regulator_set_suspend_enable regulator_get_suspend_value regulator_set_suspend_value Signed-off-by: Joseph Chen Signed-off-by: Elaine Zhang Reviewed-by: Kever Yang

regulator: Add support for ramp delay

2019-03-11T06:53:19Z

Changing voltage and enabling regulator might require delays so the regulator stabilizes at expected level. Add support for "regulator-ramp-delay" binding which can introduce required time to both enabling the regulator and to changing the voltage. Signed-off-by: Krzysztof Kozlowski Tested-by: Anand Moon Signed-off-by: Minkyu Kang

power: regulator: Introduce regulator_set_enable_if_allowed api

2019-02-09T19:50:22Z

regulator_set_enable() api throws an error in the following three cases: - when requested to disable an always-on regulator - when set_enable() ops not provided by regulator driver - when enabling is actually failed.(Error returned by the regulator driver) Sometimes consumer drivers doesn't want to track the first two scenarios and just need to worry about the case where enabling is actually failed. But it is also a good practice to have an error value returned in the first two cases. So introduce an api regulator_set_enable_if_allowed() which ignores the first two error cases and returns an error as given by regulator driver. Consumer drivers can use this api need not worry about the first two error conditions. Signed-off-by: Lokesh Vutla Reviewed-by: Simon Glass