u-boot.git/include/power, branch v2017.07

Fixup bug in PMIC TPS65217 register address definition

2017-06-09T11:25:16+00:00

The addresses of the registers in TI TPS65217 are not continuous.
     There is a gap between ENABLE(0x16) and DEFUVLO(0x18). No 0x17
     register available.

     Fixup the enum values by adding a 'reserved' placeholder to correct
     the addresses higher than 0x17.

     Series-to: Heiko Schocher 

Signed-off-by: Brock Zheng Techyauld Ltd 
Reviewed-by: Lukasz Majewski

power: pmic: lp87565: Add the basic pmic support

2017-06-09T11:25:16+00:00

Add support to bind the regulators/child nodes with the pmic.

Signed-off-by: Keerthy 
Signed-off-by: Jaehoon Chung

board: ti: AM43XX: Add ddr voltage rail configuration

2017-06-09T11:25:16+00:00

Add ddr voltage rail (dcdc3) configuration. Set the dcdc3
DDR supply to 1.35V.

Signed-off-by: Keerthy 
Reviewed-by: Tom Rini 
Reviewed-by: Lokesh Vutla

dm: pmic: Convert uclass to livetree

2017-06-01T13:03:12+00:00

Update the pmic uclass and all pmics to support a live device tree.

Signed-off-by: Simon Glass

power: pmic: tps65218: Fix tps65218_voltage_update function

2017-05-29T08:28:52+00:00

Currently while setting the vsel value for dcdc1 and dcdc2
the driver is wrongly masking the entire 8 bits in the process
clearing PFM (bit7) field as well. Hence describe an appropriate
mask for vsel field and modify only those bits in the vsel
mask.

Source: http://www.ti.com/lit/ds/symlink/tps65218.pdf

Signed-off-by: Keerthy 
Fixes: 86db550b38 ("power: Add support for the TPS65218 PMIC")
Reviewed-by: Jaehoon Chung

arm: am33xx: Fix MPU opp selection

2017-05-12T12:37:12+00:00

Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:

MPU values for PG 2.0 and later(Package ZCZ and ZCE):

 -------------------------------------------------------
|	|	  ZCZ		|	  ZCE		|
|-------------------------------------------------------|
|	| VDD[V]   | ARM [MHz]	| VDD[V]   | ARM [MHz]  |
|-------|----------|------------|----------|------------|
| NITRO |  1.325   |   1000     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
| TURBO |   1.26   |    800	|   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP120 |   1.20   |    720     |   NA     |    NA      |
|-------|----------|------------|----------|------------|
|OPP100 |   1.10   |    600     |   1.10   |    600     |
|-------|----------|------------|----------|------------|
| OPP50 |   0.95   |    300     |   0.95   |    300     |
 -------------------------------------------------------

There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.

[1] http://www.ti.com/lit/ds/symlink/am3356.pdf

Signed-off-by: Lokesh Vutla 
Reviewed-by: Tom Rini

power: rk808: rename to rk8xx

2017-05-10T19:37:22+00:00

Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.

Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`

Signed-off-by: Jacob Chen

power: pmic: rk808: add RK818 support

2017-05-10T19:37:22+00:00

The RK818 chip is a Power Management IC (PMIC) for multimedia and handheld
devices.

For boards use rk818, the input current should be set in the early stage, before
ddr initialization.

Signed-off-by: Jacob Chen

power: pmic: append rk818 regs to rk808

2017-05-10T19:37:22+00:00

Both RK808 and RK818 chips are using a similar register map,
so we can reuse them.

I have also add reg prefix to exist registers, to keep them same style.

Signed-off-by: Jacob Chen 
Reviewed-by: Simon Glass

pmic: pmic_mc34vr500: Add APIs to set/get SWx volt

2017-01-18T17:28:57+00:00

Signed-off-by: Hou Zhiqiang 
Reviewed-by: Jaehoon Chung 
Reviewed-by: York Sun