PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver and add new type for PCA9451A. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Marek Vasut <marex@denx.de>
This driver is not used. Drop it and the entire fuel_gauge directory, since there is nothing left. Signed-off-by: Simon Glass <sjg@chromium.org>
For 2023.04 ----------- - several conversion to DM_SERIAL and DM_I2C - fixes for Toradex boards - PSCI CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/14965
The highest register on ACT8846 is 0xf5, so set the number of registers to 0xf6, ensuring that the pmic read/write commands are able to access all of the supported registers (and many that are not valid, since the register space is quite sparse). Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For Rockchip boards with the all rk8xx series PMICs (excluding the rk808), it is sometimes desirable to not boot whenever the device is plugged in. An example would be for the Odroid Go Advance. This provides a configurable option to check the PMIC says it was powered because of a plug-in event. If the value is 1 and this option is selected, the device shuts down shortly after printing a message to console stating the reason why it's shutting down. Powering up the board with the power button is not affected. This patch parallels the work done in the following patch series: https://lore.kernel.org/u-boot/20220121133732.2397273-1-andre.przywara@arm.com/ Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than CONFIG_EXYNOS[45] - In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX - Migrate specific SoC CONFIG values to Kconfig - Use CONFIG_TARGET_x rather than CONFIG_x - Migrate other CONFIG_EXYNOS_x symbols to Kconfig - Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE - Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest of U-Boot usage. Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Depending on backup register value, U-Boot SPL maintains the debug unit powered-on for debugging purpose; only BUCK1 is required for powering the debug unit, so revert the setting for all the other power lanes, except BUCK3 that has to be always on. To be functional this patch requires a modification in the debugger ,openocd for example, to update the STM32MP15 backup register when it is required to debug SPL after reset. After deeper analysis this behavior will be never supported in tools so the associated code, will be never used and the associated code can be removed. Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add PCA9450 regulator driver. This is complementary driver for the BUCKn and LDOn regulators provided by the PCA9450 PMIC driver. Currently the driver permits reading the settngs and configuring the BUCKn and LDOn regulators. Reviewed-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>