u-boot.git/include/soc/qcom/geni-se.h, branch master Unnamed repository; edit this file 'description' to name the repository. misc: introduce Qcom GENI wrapper 2025-10-30T17:04:51+00:00 Casey Connolly casey.connolly@linaro.org 2025-07-14T13:13:14+00:00 b95df6ed8c21aee71b4859d9d88c6a6e32c641c8 Qualcomm peripherals like UART, SPI, I2C, etc are all exposed under a common GENI Serial Engine wrapper device. Replace the stub driver we use for this currently with a full-on misc device and implement support for loading peripheral firmware. Each of the peripherals has it's own protocol-specific firmware, this is stored on the internal storage of the device with a well-known partition type GUID. To support this, GENI will bind peripherals in two stages. First the ones that already have firmware loaded (such as the serial port) are bound in the typical way. But devices that require firmware loading are deferred until EVT_LAST_STAGE_INIT. At this point we can be sure that the storage device is available, so we load the firmware and then bind and probe the remaining children. Child devices are expected to determine if firmware loading is necessary and call qcom_geni_load_firmware(). Since Linux currently doesn't support loading firmware (and firmware may not be available), we probe all GENI peripherals to ensure that they always load firmware if necessary. Signed-off-by: Casey Connolly <casey.connolly@linaro.org> Link: https://patch.msgid.link/20250714-geni-load-fw-v5-3-5abbc0d29838@linaro.org Signed-off-by: Casey Connolly <kcxt@postmarketos.org> 
Qualcomm peripherals like UART, SPI, I2C, etc are all exposed under a
common GENI Serial Engine wrapper device. Replace the stub driver we use
for this currently with a full-on misc device and implement support for
loading peripheral firmware.

Each of the peripherals has it's own protocol-specific firmware, this is
stored on the internal storage of the device with a well-known partition
type GUID.

To support this, GENI will bind peripherals in two stages. First the
ones that already have firmware loaded (such as the serial port) are
bound in the typical way. But devices that require firmware loading are
deferred until EVT_LAST_STAGE_INIT. At this point we can be sure that
the storage device is available, so we load the firmware and then bind
and probe the remaining children.

Child devices are expected to determine if firmware loading is necessary
and call qcom_geni_load_firmware().

Since Linux currently doesn't support loading firmware (and firmware may
not be available), we probe all GENI peripherals to ensure that they
always load firmware if necessary.

Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-3-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
i2c: Add support for Qualcomm Generic Interface (GENI) I2C controller 2024-04-23T11:29:32+00:00 Neil Armstrong neil.armstrong@linaro.org 2024-04-22T09:33:52+00:00 75db9ede12d06693a3ced8c901b74065a1922a23 Add Support for the Qualcomm Generic Interface (GENI) I2C interface found on newer Qualcomm SoCs. The Generic Interface (GENI) is a firmware based Qualcomm Universal Peripherals (QUP) Serial Engine (SE) Wrapper which can support multiple bus protocols depending on the firmware type loaded at early boot time based on system configuration. It also supports the "I2C Master Hub" which is a single function Wrapper that only FIFO mode I2C. It replaces the fixed-function QUP Wrapper found on older SoCs. The geni-se.h containing the generic GENI Serial Engine registers defines is imported from Linux. Only FIFO mode is implemented, neither SE DMA nor GPI DMA are implemented. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> 
Add Support for the Qualcomm Generic Interface (GENI) I2C interface
found on newer Qualcomm SoCs.

The Generic Interface (GENI) is a firmware based Qualcomm Universal
Peripherals (QUP) Serial Engine (SE) Wrapper which can support multiple
bus protocols depending on the firmware type loaded at early boot time
based on system configuration.

It also supports the "I2C Master Hub" which is a single function Wrapper
that only FIFO mode I2C.

It replaces the fixed-function QUP Wrapper found on older SoCs.

The geni-se.h containing the generic GENI Serial Engine registers defines
is imported from Linux.

Only FIFO mode is implemented, neither SE DMA nor GPI DMA are implemented.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>