(0xf5000000, to be specific). The reason is that the RTC first gets
accessed before MMU is initialized and, consequently, it needs to be
placed at physical addresses which are later mapped to the same
virtual addresses (like 0xf5000000 physical is mapped to 0xf5000000
virtual).

- hymod update
- cleanup (especially for gcc-3.x compilers)

added CONFIG_750FX support for IBM 750FX processors

  Fix clock divider rounding problem in drivers/serial.c

* Patch by Ken Chou, 19 June 2003:
  Added support for A3000 SBC board (Artis Microsystems Inc.)

- Hymod board database mods: add "who" field and new xilinx chip types
- provide new "init_cmd_timeout()" function so code external to
  "common/main.c" can use the "reset_cmd_timeout()" function before
  entering the main loop
- add DTT support for adm1021 (new file dtt/adm1021.c; config
  slightly different. see include/configs/hymod.h for an example
  (requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
  CFG_DTT_ADM1021 defined)
- add new "eeprom_probe()" function which has similar args and
  behaves in a similar way to "eeprom_read()" etc.
- add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
  function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
- gdbtools copyright update
- ensure that set_msr() executes the "sync" and "isync" instructions
  after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
- 8260 I/O ports fix: Open Drain should be set last when configuring
- add SIU IRQ defines for 8260
- allow LDSCRIPT override and OBJCFLAGS initialization: change to
  config.mk to allow board configurations to override the GNU
  linker script, selected via the LDSCRIPT, make variable, and to
  give an initial value to the OBJCFLAGS make variable
- 8260 i2c enhancement:
  o correctly extends the timeout depending on the size of all
    queued messages for both transmit and receive
  o will not continue with receive if transmit times out
  o ensures that the error callback is done for all queued tx
    and rx messages
  o correctly detects both tx and rx timeouts, only delivers one to
    the callback, and does not overwrite an earlier error
  o logic in i2c_probe now correct
- add "vprintf()" function so that "panic()" function can be
  technically correct
- many Hymod board changes

- add support for Logotronic DL datalogger board
- cleanup serial line after kermit binary download
- add debugX macro (debug level support)
- update mach-types.h to latest arm.linux.org.uk master list.

  - rewrite of the S3C24X0 register definitions stuff
  - "driver" for the built-in S3C24X0 RTC

* Patches by Yuli Barcohen, 12 Jun 2003:
  - Add MII support and Ethernet PHY initialization for MPC8260ADS board
  - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
    configuration word supplied by FPGA on some MPC8260ADS boards

* Patch by Pantelis Antoniou, 10 Jun 2003:
  Unify status LED interface

  Modifications for Atmel AT91RM9200DK ARM920T based development kit
  - Add Atmel DataFlash support for reading and writing.
  - Add possibility to boot a Linux from DataFlash with BOOTM command.
  - Add Flash detection on Atmel AT91RM9200DK
    (between Atmel AT49BV1614 and AT49BV1614A flashes)
  - Replace old Ethernet PHY layer functions
  - Change link address

* Patch by Frank Smith, 9 Jun 2003:
  use CRIT_EXCEPTION for machine check on 4xx

* Patch by Detlev Zundel, 13 Jun 2003:
  added implementation of the "carinfo" command in cmd_immap.c

* Patches by Kyle Harris, 13 Mar 2003:
  - Add FAT partition support
  - Add command support for FAT
  - Add command support for MMC
  ----
  - Add Intel PXA support for video
  - Add Intel PXA support for MMC
  ----
  - Enable MMC and FAT for lubbock board
  - Other misc changes for lubbock board